|
Specific Gravity
|
|
|
|
|
--
|
|
|
ASTM D792 |
|
--
|
|
g/cm³
|
ISO 1183 |
|
Specific Volume
|
|
in³/lb
|
ASTM D792 |
|
Melt Mass-Flow Rate (MFR)
|
|
g/10 min
|
ASTM D1238 |
|
Molding Shrinkage
|
|
|
|
|
Flow
|
|
in/in
|
ASTM D955 |
|
Across Flow
|
|
in/in
|
ASTM D955 |
|
Across Flow
|
|
%
|
ISO 294-4 |
|
Flow
|
|
%
|
ISO 294-4 |
|
Water Absorption
|
|
|
|
|
73°F, 24 hr
|
|
%
|
ASTM D570 |
|
Saturation, 73°F
|
|
%
|
ISO 62 |
|
Spiral Flow
|
|
|
Internal Method |
|
Tensile Modulus
|
|
psi
|
ISO 527-2/1A/1 |
|
Tensile Strength
|
|
|
|
|
Break, 73°F
|
|
psi
|
ASTM D638 |
|
Break
|
|
psi
|
ISO 527-2/1A/5 |
|
Tensile Elongation
|
|
|
|
|
Break, 73°F
|
|
%
|
ASTM D638 |
|
Break
|
|
%
|
ISO 527-2/1A/5 |
|
Flexural Modulus
|
|
|
|
|
73°F
|
|
psi
|
ASTM D790 |
|
73°F
|
|
psi
|
ISO 178 |
|
Flexural Strength
|
|
|
|
|
73°F
|
|
psi
|
ASTM D790 |
|
-- 2
|
|
psi
|
ISO 178 |
|
Charpy Notched Impact Strength
|
|
|
ISO 179/1eA |
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
|
Charpy Unnotched Impact Strength
|
|
|
ISO 179/1eU |
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
|
Notched Izod Impact
|
|
|
|
|
73°F
|
|
ft·lb/in
|
ASTM D256 |
|
-22°F
|
|
ft·lb/in²
|
ISO 180/1A |
|
73°F
|
|
ft·lb/in²
|
ISO 180/1A |
|
Unnotched Izod Impact
|
|
|
|
|
73°F
|
|
ft·lb/in
|
ASTM D256 |
|
73°F
|
|
ft·lb/in²
|
ISO 180/1U |
|
Rockwell Hardness (M-Scale)
|
|
|
ASTM D785, ISO 2039-2 |
|
Deflection Temperature Under Load
|
|
|
|
|
66 psi, Unannealed
|
|
°F
|
ASTM D648 |
|
264 psi, Unannealed
|
|
°F
|
ASTM D648 |
|
264 psi, Unannealed
|
|
°F
|
ISO 75-2/A |
|
1160 psi, Unannealed
|
|
°F
|
ISO 75-2/C |
|
Glass Transition Temperature
|
|
°F
|
ISO 11357-2 |
|
Melting Temperature 3
|
|
°F
|
ISO 11357-3 |
|
CLTE
|
|
|
ISO 11359-2 |
|
Flow
|
|
in/in/°F
|
|
|
Transverse
|
|
in/in/°F
|
|
|
Surface Resistivity
|
|
ohms
|
IEC 60093 |
|
Volume Resistivity
|
|
|
|
|
--
|
|
ohm·cm
|
ASTM D257 |
|
--
|
|
ohm·cm
|
IEC 60093 |
|
Dielectric Strength
|
|
|
|
|
-- 4
|
|
V/mil
|
ASTM D149 |
|
--
|
|
V/mil
|
IEC 60243-1 |
|
Dielectric Constant
|
|
|
|
|
1 kHz
|
|
|
ASTM D150 |
|
1 MHz
|
|
|
ASTM D150 |
|
10 kHz
|
|
|
IEC 60250 |
|
1 MHz
|
|
|
IEC 60250 |
|
Dissipation Factor
|
|
|
|
|
1 kHz
|
|
|
ASTM D150 |
|
1 MHz
|
|
|
ASTM D150 |
|
10 kHz
|
|
|
IEC 60250 |
|
1 MHz
|
|
|
IEC 60250 |
|
Arc Resistance
|
|
sec
|
ASTM D495 |
|
Comparative Tracking Index
|
|
V
|
IEC 60112 |
|
Flame Rating - UL
|
|
|
UL 94 |
|
0.0150 in
|
|
|
|
|
0.0591 in
|
|
|
|
|
Melt Specific Heat
|
|
Btu/lb/°F
|
ASTM C351 |
|
CSA Rating (33.1 mil)
|
|
|
CSA F-1 |
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Fortron® 1140L6, Fortron 1140L6, Fortron® , Fortron, Fortron1140L6, 1140 L 6, 1140L6, 1140L, L6, Polyphenylene Sulfide, PPS, Ticona, PolyphenyleneSulfide, L1140
|
|
Features may also be described by the following terms: Good Flow, Zero Halogen Content, Halogen Free.
|
|
Uses may also be described by the following terms: Thin-walled Parts, Thin Walled Parts, Thin-wall Parts, Thin wall Parts, Thinwall Parts, Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector.
|
|
This plastic material has approval for 3 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (2), GM (1).
|