IDES Prospector Already have an account? Login Here

IDES

Lucet® N127-LD

Acetal (POM) Copolymer

Supplied by LG Chem Ltd.

The technical datasheet with complete property values for Lucet® N127-LD is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Copolymer
  • Good Abrasion Resistance
  • Good Chemical Resistance
  • Good Creep Resistance
  • Good Dimensional Stability
  • Good Flow
  • Good Moldability
  • Good Thermal Stability
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength (Yield)
psi
 ASTM D790
Coefficient of Friction (vs. Itself - Static)
 
 ASTM D1894
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
     ASTM D256
-40°F
ft·lb/in
  
73°F
ft·lb/in
  
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Dielectric Constant (1 MHz)
 
 ASTM D150
Dissipation Factor (1 MHz)
 
 ASTM D150
Arc Resistance (0.125 in)
sec
 ASTM D495
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0313 in)
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Lucet® N127-LD, Lucet N127LD, Lucet® , Lucet, LucetN127LD, N 127, N 127 LD, N127-LD, N127LD, N127:LD, N127/LD, N127+LD, N127_LD, N127 LD, N127, 127LD, Acetal Copolymer, Acetal Copolymer, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, LG Chem, AcetalPOMCopolymer, 127N
Features
Features may also be described by the following terms: Good Abrasion Resistance, Abrasion Resistant, Good Chemical Resistance, Chemical Resistant, Good Creep Resistance, Creep Resistant, Good Dimensional Stability, Dimensionally Stable, Good Flow, Good Moldability, Good Thermal Stability.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Back Pressure
psi
  
Screw Speed
rpm
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.