IDES Prospector Already have an account? Login Here

IDES

Ipiranga GM 5010 T2

High Density Polyethylene

Supplied by Braskem

The technical datasheet with complete property values for Ipiranga GM 5010 T2 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
The GM 5010 T2 is a High Density Polyethylene compounding with high molar mass, specially developed for the manufacturing of extruded pipes. This resin is produced with bimodal technology, it has excellent mechanical properties, besides excellent resistance to stress cracking. This resin has MRS (Minimum Required Strength) of 8 MPa according to ISO 9080, and is classified as PE 80 according to ISO 12162. GM 5010 T2 contains carbon black pigment that guarantees resistance against photodegradation.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Additive 
  • Carbon Black (22500 ppm)
Features 
  • Good Crack Resistance
  • Good UV Resistance
  • High Density
  • High Molecular Weight
  
Uses 
  • Cable Jacketing
  • Geo Membranes
  • Irrigation Applications
  • Mining Applications
  • Piping
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Pipe Extrusion
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (190°C/5.0 kg)
g/10 min
 ASTM D1238
Environmental Stress-Cracking Resistance (122°F, 0.0787 in, 100% Igepal, Compression Molded, F50)
hr
 ASTM D1693B
Carbon Black Content
%
 ASTM D1603
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
     ASTM D638
Yield, Compression Molded
psi
  
Break, Compression Molded
psi
  
Tensile Elongation
     ASTM D638
Yield, Compression Molded
%
  
Break, Compression Molded
%
  
Flexural Modulus - 2% Secant (Compression Molded)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F, Compression Molded)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D, 15 sec, Compression Molded)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (66 psi, Unannealed, Compression Molded)
°F
 ASTM D648
Vicat Softening Temperature
°F
 ASTM D1525 2
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Ipiranga GM 5010 T2, Ipiranga , IpirangaGM5010T2, GM 5010 T 2, GM 5010 T2, GM5010, 5010T, T2, GM5010T2, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, Braskem, PolyethyleneHighDensity, 5010GM
Features
Features may also be described by the following terms: High Density, High Specific Gravity, High Molecular Weight, High MW, Good Crack Resistance, Crack Resistant, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Uses
Uses may also be described by the following terms: Piping, Pipe, Geomembranes, Geo Membranes.
Agency Ratings
This plastic material has 3 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): ASTM (1), ISO (2).
Notes
1Typical properties: these are not to be construed as specifications.
2Loading 1 (10 N)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.