IDES Prospector Already have an account? Login Here

IDES

Sarlink® 3145D

Thermoplastic Vulcanizate

Supplied by Teknor Apex Company (Sarlink)

The technical datasheet with complete property values for Sarlink® 3145D is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
SARLINK® 3145D is a high hardness, multi-purpose thermoplastic elastomer featuring excellent resiliency, heat resistance and flex fatigue resistance. SARLINK® 3145D can be processed by injection molding, extrusion and blow molding to produce clamps, grommets, profiles, boots, ducts and bellows.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
  • South America
  
Features 
  • Fatigue Resistant
  • High Hardness
  • Medium Heat Resistance
  • Resilient
  
Uses 
  • Grommets
  • Profiles
  
Automotive Specifications 
Forms 
  • Pellets
Processing Method 
  • Blow Molding
  • Extrusion
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress     ISO 37
Across Flow: 100% Strain
psi
  
Flow: 100% Strain
psi
  
Tensile Stress     ISO 37
Across Flow: Break
psi
  
Flow: Break
psi
  
Tensile Elongation     ISO 37
Across Flow: Break
%
  
Flow: Break
%
  
Tear Strength - Across Flow 2
lbf/in
 ISO 34-1
Compression Set     ISO 815
73°F, 22.0 hr
%
  
158°F, 22.0 hr
%
  
257°F, 70.0 hr
%
  
Hardness
Nominal Value
Unit
Test Method
Shore Hardness     ISO 868
Shore D, 5 sec, Extruded
 
  
Shore D, 5 sec, Injection Molded
 
  
Aging
Nominal Value
Unit
Test Method
Change in Tensile Strength in Air - Across Flow     ISO 188
275°F, 1000 hr
%
  
100% Strain 275°F, 1000 hr
%
  
302°F, 168 hr
%
  
100% Strain 302°F, 168 hr
%
  
Change in Tensile Strain at Break in Air - Across Flow     ISO 188
275°F, 1000 hr
%
  
302°F, 168 hr
%
  
Change in Shore Hardness in Air     ISO 188
Shore D, 275°F, 1000 hr
 
  
Shore D, 302°F, 168 hr
 
  
Change in Volume (257°F, 70 hr, in IRM 903 Oil)
%
 ISO 1817
Additional Information
Nominal Value
Unit
Test Method
Apparent Shear Viscosity - Capillary, 206 1/s (392°F)
Pa·s
 ISO 11443
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Sarlink® 3145D, Sarlink 3145D, Sarlink® , Sarlink, Sarlink3145D, 3145 D, 3145D, Thermoplastic Vulcanizate, TPV, Thermoplastic Elastomer, TPE, ThermoplasticVulcanizate, ThermoplasticElastomer, D3145
Features
Features may also be described by the following terms: High Hardness, Hard, Medium Heat Resistance.
Automotive Specifications
This plastic material has approval for 6 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (4), OPEL (2).
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Melt Temperature
°F
  
Die Temperature
°F
  
Take-Off Roll
°F
  
Extrusion Notes
Screen Pack: 20 to 60 mesh
Screw: general purpose
Compression Ratio: 3:1
Notes
1Typical properties: these are not to be construed as specifications.
2Method Ba, Angle (Unnicked)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.