IDES Prospector Already have an account? Login Here

IDES

Pebax® 7033 SA 01

Polyether Block Amide

Supplied by Arkema

The technical datasheet with complete property values for Pebax® 7033 SA 01 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Features 
  • Good Chemical Resistance
  • Good Colorability
  • Good Impact Resistance
  • Good Processability
  • Good Toughness
  • High Strength
  • Low Temperature Impact Resistance
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (235°C/1.0 kg)
g/10 min
 ASTM D1238
Molding Shrinkage
     ASTM D955
Flow
in/in
  
Across Flow
in/in
  
Water Absorption
     ASTM D570
24 hr
%
  
Equilibrium, 73°F, 50% RH
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Ultimate)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Taber Abrasion Resistance (1000 Cycles, 1000 g, H-18 Wheel)
mg
 ASTM D1044
Elastomers
Nominal Value
Unit
Test Method
Tear Strength 2
lbf/in
 ASTM D624
Compression Set (160°F, 24.0 hr)
%
 ASTM D395
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
     ASTM D256
-40°F
ft·lb/in
  
68°F
 
  
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (66 psi, Unannealed)
°F
 ASTM D648
Vicat Softening Temperature
°F
 ASTM D1525
Melting Temperature
°F
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Pebax® 7033 SA 01, Pebax 7033 SA 01, Pebax® , Pebax, Pebax7033SA01, 7033 SA 01, 7033SA, SA01, 7033SA01, Polyether Block Amide, PEBA-Ether, PEBAEther, PEBA:Ether, PEBA/Ether, PEBA+Ether, PEBA_Ether, PEBA Ether, Thermoplastic Elastomer, TPE, Arkema, PolyetherBlockAmide, ThermoplasticElastomer, SA7033
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant, Good Colorability, Good Processability, Easy Processing, High Strength, Good Toughness, Tough, Good Impact Resistance, Low Temperatuer Impact Resistance, Low Temp Impact Resistance.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Regrind
%
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Screw L/D Ratio
 
  
Screw Compression Ratio
 
  
Notes
1Typical properties: these are not to be construed as specifications.
2Die C
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.