IDES Prospector Already have an account? Login Here

IDES

UBE Nylon 1030 B

Polyamide 6

Supplied by UBE Engineering Plastics, S.A.

The technical datasheet with complete property values for UBE Nylon 1030 B is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
UBE NYLON 1030 B is a high viscosity, unmodified Polyamide 6 for general application (tubes, film, sheets).
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Food Contact Acceptable
  • General Purpose
  • Good Processability
  • High Viscosity
  
Uses 
  • Film
  • Sheet
  • Tubing
Agency Ratings 
 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Mechanical
Nominal Value
Unit
Test Method
Coefficient of Friction
     ASTM D1894
vs. Itself - Dynamic
 
  
vs. Itself - Static
 
  
Films
Nominal Value
Unit
Test Method
Secant Modulus - MD (Cast Film)
psi
 ASTM D882
Tensile Strength - MD
     ASTM D882
Yield, Cast Film
psi
  
Break, Cast Film
psi
  
Tensile Elongation - MD (Break, Cast Film)
%
 ASTM D882
Thermal
Nominal Value
Unit
Test Method
Melting Temperature (DSC)
°F
 ISO 3146
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257
Optical
Nominal Value
Unit
Test Method
Gardner Gloss
 
 ASTM D523
Haze
%
 ASTM D1003
Additional Information
The value listed as Melting Temperature, ISO 3146, was tested in accordance with ISO 11357.
The value listed as Surface Resistivity, ASTM D257, was tested in accordance with UBE test methods.
Coefficient of Friction, ASTM D1894, Dynamic: >1
Coefficient of Friction, ASTM D1894, Static: >1
Oxygen Permeability, ASTM D3985: 40 ml/m²/day
Relative Viscosity, JIS K6810, 96% H2SO4, conc. 1.0 g/100 ml: 4.18
Extractable Content, JIS K6810: <1.0 wt%
Water Vapor Permeability, JIS Z0208: 120 g/m²/day
Piercing Strength, JAS P1019, Cast Film: 10.0 N
Piercing Elongation, JAS P1019, Cast Film: 15 mm
Flex Crack Resistance, MIL B131B, 23°C, 1000 cycle, Cast Film: <15 hole/0.04 m²
Gelbo Test, MIL B131B, 5°C, 100 cycle, Cast Film: <5 hole/0.04 m²
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: UBE Nylon 1030 B, UBE Nylon , UBENylon1030B, UBENylon, Nylon 1030 B, Nylon1030 B, Nylon1030, Nylon, Nylon1030B, 1030 B, 1030B, Polyamide 6, Nylon 6, Polyamide, pa6, UBE Engineering Plastics, Polyamide6, Nylon6, B1030, 1030Nylon
Generic Name
Generic Name may also be described by the following terms: PA6.
Features
Features may also be described by the following terms: High Viscosity, Good Processability, Easy Processing.
Uses
Uses may also be described by the following terms: Tubing, Tube.
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1), EU (1).
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.