IDES Prospector Already have an account? Login Here

IDES

Clariant Nylon 6/6 PA-111G43

Polyamide 66

Glass Fiber Reinforcement, 43%

Supplied by Clariant Performance Plastics

The technical datasheet with complete property values for Clariant Nylon 6/6 PA-111G43 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 43% Filler by Weight
Features 
  • Good Stiffness
  • High Strength
  
Uses 
  • Automotive Applications
  • Gears
  • Industrial Applications
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow (0.125 in)
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.125 in)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness
     ASTM D785
M-Scale
 
  
R-Scale
 
  
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
Melting Temperature
°F
  
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0625 in)
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Clariant Nylon 6/6 PA-111G43, Clariant Nylon 66 PA111G43, Clariant Nylon 6/6 , Clariant Nylon 66, Clariant Nylon 6:6, Clariant Nylon 6+6, Clariant Nylon 6-6, Clariant Nylon 6_6, Clariant Nylon 6 6, ClariantNylon66PA111G43, ClariantNylon66, 6 6 PA 111 G 43, 6 6 PA, ClariantNylon6_6, PA, 6/6PA-111G43, 66PA111G43, 6:6PA-111G43, 6+6PA-111G43, 6-6PA-111G43, 6_6PA-111G43, 6 6PA-111G43, 6/6PA:111G43, 6/6PA/111G43, 6/6PA+111G43, 6/6PA_111G43, 6/6PA 111G43, 66, 6PA, 6/6PA, 66PA, 6:6PA, 6+6PA, 6-6PA, 6_6PA, 6 6PA, PA 111 G 43, 6_6PA111G43, 6 6PA111G43, 66PA_111G43, 66PA 111G43, PA-111G43, PA111G43, PA:111G43, PA/111G43, PA+111G43, PA_111G43, PA 111G43, PA111, 111G, G43, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Clariant Perf, Polyamide66, Nylon66, 111PA
Generic Name
Generic Name may also be described by the following terms: PA66.
Features
Features may also be described by the following terms: Good Stiffness, High Strength.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): UL (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Melt Temperature (Aim)
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Back Pressure
psi
  
Screw Speed
rpm
  
Cushion
in
  
Injection Notes
Injection Pressure: Use minimum pressure to achieve 95% fill during the boost inj. pressure phase.
Hold Pressure: 30% to 75% of injection pressure.
Mold Temp. Target: 180°F
Screw Speed Target: 75 RPM
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.