Impet 330R Ticona Polyethylene Terephthalate (Glass Fiber Reinforcement, 30%)

Product Description

Impet 330R is a 30% glass reinforced injection moldable polyester containing post consumer recycled PET. It provides an excellent combination of strength, stiffness, and high temperature resistance.

General

Material Status

Commercial: Active

Availability

Africa & Middle East

Asia Pacific

Europe

Latin America

North America

South America

Filler / Reinforcement

Glass Fiber Reinforcement, 30% Filler by Weight

Recycled Content

Features

Good Stiffness

Good Strength

High Heat Resistance

RoHS Compliance

Automotive Specifications

Processing Method

Injection Molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity
--			ASTM D792
--		g/cm³	ISO 1183
Molding Shrinkage
Flow		in/in	ASTM D955
Across Flow		%	ISO 294-4
Flow		%	ISO 294-4
Water Absorption (Equilibrium, 73°F, 50% RH)		%	ISO 62
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus		psi	ISO 527-2/1A/1
Tensile Strength
Break, 73°F		psi	ASTM D638
Break		psi	ISO 527-2/1A/5
Tensile Elongation
Break, 73°F		%	ASTM D638
Break		%	ISO 527-2/1A/5
Flexural Modulus
73°F		psi	ASTM D790
73°F		psi	ISO 178
Flexural Strength
73°F		psi	ASTM D790
73°F		psi	ISO 178
Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength			ISO 179/1eA
-22°F		ft·lb/in²
73°F		ft·lb/in²
Charpy Unnotched Impact Strength			ISO 179/1eU
-22°F		ft·lb/in²
73°F		ft·lb/in²
Notched Izod Impact
73°F		ft·lb/in	ASTM D256
73°F		ft·lb/in²	ISO 180/1A
Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature
66 psi, Unannealed		°F	ISO 75-2/B
264 psi, Unannealed		°F	ASTM D648, ISO 75-2/A
Glass Transition Temperature		°F	ISO 11357-2
Melting Temperature²		°F	ISO 11357-3
CLTE			ISO 11359-2
Flow		in/in/°F
Transverse		in/in/°F
Electrical	Nominal Value	Unit	Test Method
Surface Resistivity
--		ohms	ASTM D257
--		ohms	IEC 60093
Volume Resistivity
--		ohm·cm	ASTM D257
--		ohm·cm	IEC 60093
Dielectric Strength
--³		V/mil	ASTM D149
--		V/mil	IEC 60243-1
Dielectric Constant
1 kHz			ASTM D150
10 kHz			ASTM D150
100 Hz			IEC 60250
1 MHz			IEC 60250
Dissipation Factor
1 kHz			ASTM D150
10 kHz			ASTM D150
1 MHz			IEC 60250
Arc Resistance		sec	ASTM D495
Comparative Tracking Index
--		V	IEC 60112
--		V	ASTM D3638
Flammability	Nominal Value	Unit	Test Method
Flame Rating - UL			UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Impet® 330R, Impet 330R, Impet® , Impet, Impet330R, 330 R, 330R, Polyethylene Terephthalate, PET, Polyester, Ticona, PolyethyleneTerephthalate, R330
Features
Features may also be described by the following terms: High Heat Resistance, Good Stiffness, Good Strength.
Automotive Specifications
This plastic material has approval for 9 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): CHRYSLER (1), FORD (2), DELPHI (1), ASTM (1), AC (1), GM (3).

Injection	Nominal Value	Unit
Suggested Max Regrind		%
Rear Temperature		°F
Middle Temperature		°F
Front Temperature		°F
Nozzle Temperature		°F
Processing (Melt) Temp		°F
Mold Temperature		°F
Injection Rate
Back Pressure		psi
Screw Speed		rpm
Injection Notes
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.

Notes

¹Typical properties: these are not to be construed as specifications.

²10°C/min

³Method A (Short-Time)

Impet® 330R

Polyethylene Terephthalate

Glass Fiber Reinforcement, 30%

Supplied by Ticona