Impet 830R Ticona Polyethylene Terephthalate (Glass\Mineral, 35%)

Product Description

Impet 830R is a 35% glass/mineral reinforced injection moldable polyester made with recycled PET. It provides an excellent combination of strength, stiffness, warp resistance, and high temperature capability together with excellent processability (high flow) during molding.

General

Material Status

Commercial: Active

Availability

Africa & Middle East

Asia Pacific

Europe

Latin America

North America

South America

Filler / Reinforcement

Glass\Mineral, 35% Filler by Weight

Recycled Content

Features

Good Processability

Good Stiffness

Good Strength

High Flow

High Heat Resistance

Warp Resistant

RoHS Compliance

Automotive Specifications

Processing Method

Injection Molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity
--			ASTM D792
--		g/cm³	ISO 1183
Molding Shrinkage - Flow		%	ISO 294-4
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus		psi	ISO 527-2/1A/1
Tensile Strength
Break, 73°F		psi	ASTM D638
Break		psi	ISO 527-2/1A/5
Tensile Elongation
Break, 73°F		%	ASTM D638
Break		%	ISO 527-2/1A/5
Flexural Modulus
73°F		psi	ASTM D790
73°F		psi	ISO 178
Flexural Strength
73°F		psi	ASTM D790
73°F		psi	ISO 178
Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength (73°F)		ft·lb/in²	ISO 179/1eA
Notched Izod Impact
73°F		ft·lb/in	ASTM D256
73°F		ft·lb/in²	ISO 180/1A
Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature
66 psi, Unannealed		°F	ISO 75-2/B
264 psi, Unannealed		°F	ASTM D648
264 psi, Unannealed		°F	ISO 75-2/A
CLTE			ISO 11359-2
Flow		in/in/°F
Transverse		in/in/°F
Electrical	Nominal Value	Unit	Test Method
Surface Resistivity		ohms	ASTM D257
Volume Resistivity		ohm·cm	ASTM D257
Dielectric Strength²		V/mil	ASTM D149
Dielectric Constant (10 kHz)			ASTM D150
Dissipation Factor (10 kHz)			ASTM D150
Arc Resistance		sec	ASTM D495
Comparative Tracking Index		V	ASTM D3638
Flammability	Nominal Value	Unit	Test Method
Flame Rating - UL			UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Impet® 830R, Impet 830R, Impet® , Impet, Impet830R, 830 R, 830R, Polyethylene Terephthalate, PET, Polyester, Ticona, PolyethyleneTerephthalate, R830
Features
Features may also be described by the following terms: High Heat Resistance, Good Processability, Easy Processing, Good Stiffness, Warp Resistant, Warpage Resistant, High Flow, High Melt, High MFI, Good Strength.
Automotive Specifications
This plastic material has approval for 8 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (2), DELPHI (1), CHRYSLER (1), GM (3), ASTM (1).

Injection	Nominal Value	Unit
Suggested Max Regrind		%
Rear Temperature		°F
Middle Temperature		°F
Front Temperature		°F
Nozzle Temperature		°F
Processing (Melt) Temp		°F
Mold Temperature		°F
Injection Rate
Back Pressure		psi
Screw Speed		rpm
Injection Notes
Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.

Notes

¹Typical properties: these are not to be construed as specifications.

²Method A (Short-Time)

Impet® 830R

Polyethylene Terephthalate

Glass\Mineral, 35%

Supplied by Ticona