IDES Prospector Already have an account? Login Here

IDES

NORYL* EM7304F Resin

Polyphenylene Ether + PS

Glass Fiber Reinforcement, 15%

Supplied by SABIC Innovative Plastics

The technical datasheet with complete property values for NORYL* EM7304F Resin is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
15% glass reinforced, high flow with enhanced polyurethane foam adhesion for instrument panel retainers.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 15% Filler by Weight
Features 
  • Good Adhesion
  • High Flow
  
Uses 
  • Automotive Applications
  • Automotive Instrument Panel
  
Automotive Specifications 
Processing Method 
  • Injection Molding
Multi-Point Data 
  • Coefficient of Thermal Expansion vs. Temperature (ASTM E831)
  • Flexural DMA (ASTM D4065)
  • Pressure-Volume-Temperature (PVT - Zoller Method)
  • Shear DMA (ASTM D4065)
  • Specific Heat vs. Temperature (ASTM D3417)
  • Tensile Creep (ASTM D2990)
  • Tensile Fatigue
  • Tensile Stress vs. Strain (ASTM D638)
  • Thermal Conductivity vs. Temperature (ASTM E1530)
  • Viscosity vs. Shear Rate (ASTM D3835)
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage
     Internal Method
Flow: 0.126 in
in/in
  
Across Flow: 0.126 in
in/in
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (Break)
psi
 ASTM D638
Tensile Elongation 2 (Break)
%
 ASTM D638
Flexural Modulus 3 (3.94 in Span)
psi
 ASTM D790
Flexural Strength 3 (Yield, 3.94 in Span)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed, 0.252 in)
°F
 ASTM D648
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics, GE Polymerland

Product names can be difficult to match. You may have searched any one of these terms to find this product: NORYL* EM7304F Resin, NORYL EM7304F Resin, NORYL* , NORYL, NORYLEM7304FResin, EM 7304 F Resin, EM7304F Resin, EM7304, 7304F, FResin, EM7304FResin, Polyphenylene Ether + PS, Polyphenylene Ether PS, Polyphenylene Ether : PS, Polyphenylene Ether / PS, Polyphenylene Ether - PS, Polyphenylene Ether _ PS, Polyphenylene Ether PS, PPE+PS, PPEPS, PPE:PS, PPE/PS, PPE-PS, PPE_PS, PPE PS, Polyphenylene Ether, PPE, SABIC IP, PolyphenyleneEtherPS, PolyphenyleneEther, PolyphenyleneEther_PS, 7304EM
Generic Name
Generic Name may also be described by the following terms: PPO.
Features
Features may also be described by the following terms: High Flow, High Melt, High MFI, Good Adhesion.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector, Automotive Instrument Panel, Automotive Dash Board.
Automotive Specifications
This plastic material has approval for 3 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (1), CHRYSLER (1), GM (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Drying Time, Maximum
hr
  
Suggested Max Moisture
%
  
Suggested Shot Size
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Vent Depth
in
  
Notes
1Typical properties: these are not to be construed as specifications.
2Type I, 0.20 in/min
30.10 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.