IDES Prospector Already have an account? Login Here

IDES

NORYL GTX* GTX918W Resin

Polyphenylene Ether + PS + Nylon

Supplied by SABIC Innovative Plastics

The technical datasheet with complete property values for NORYL GTX* GTX918W Resin is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
High flow NORYL GTX resin for under-the-hood and electrical applications requiring retention of properties under thermal load
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • High Flow
Uses 
  • Automotive Electronics
  • Automotive Under the Hood
  
Automotive Specifications 
Processing Method 
  • Injection Molding
Multi-Point Data 
  • Coefficient of Thermal Expansion vs. Temperature (ASTM E831)
  • Flexural DMA (ASTM D4065)
  • Instrumented Impact (Energy) (ASTM D3763)
  • Instrumented Impact (Load) (ASTM D3763)
  • Pressure-Volume-Temperature (PVT - Zoller Method)
  • Shear DMA (ASTM D4065)
  • Specific Heat vs. Temperature (ASTM D3417)
  • Tensile Creep (ASTM D2990)
  • Tensile Fatigue
  • Tensile Stress vs. Strain (ASTM D638)
  • Thermal Conductivity vs. Temperature (ASTM E1530)
  • Viscosity vs. Shear Rate (ASTM D3835)
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage     Internal Method
Flow: 0.126 in
in/in
  
Across Flow: 0.126 in
in/in
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (Yield)
psi
 ASTM D638
Tensile Elongation 2 (Break)
%
 ASTM D638
Flexural Modulus 3 (1.97 in Span)
psi
 ASTM D790
Flexural Strength 3 (Yield, 1.97 in Span)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Instrumented Dart Impact (73°F, Energy at Peak Load)
in·lb
 ASTM D3763
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load     ASTM D648
66 psi, Unannealed, 0.126 in
°F
  
264 psi, Unannealed, 0.126 in
°F
  
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics, GE Polymerland

Product names can be difficult to match. You may have searched any one of these terms to find this product: NORYL GTX* GTX918W Resin, NORYL GTX GTX918W Resin, NORYL GTX* , NORYL GTX, NORYLGTXGTX918WResin, NORYLGTX, GTX 918 W Resin, GTX918W Resin, GTX918, 918W, WResin, GTX918WResin, Polyphenylene Ether + PS + Nylon, Polyphenylene Ether PS Nylon, Polyphenylene Ether : PS : Nylon, Polyphenylene Ether / PS / Nylon, Polyphenylene Ether - PS - Nylon, Polyphenylene Ether _ PS _ Nylon, Polyphenylene Ether PS Nylon, PPE+PS+Nylon, PPEPSNylon, PPE:PS:Nylon, PPE/PS/Nylon, PPE-PS-Nylon, PPE_PS_Nylon, PPE PS Nylon, Polyphenylene Ether, PPE, SABIC IP, PolyphenyleneEtherPSNylon, PolyphenyleneEther, PolyphenyleneEther_PS_Nylon, 918GTX
Features
Features may also be described by the following terms: High Flow, High Melt, High MFI.
Automotive Specifications
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Drying Time, Maximum
hr
  
Suggested Max Moisture
%
  
Suggested Shot Size
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Vent Depth
in
  
Injection Notes
Minimum Moisture Content: 0.02 %
Notes
1Typical properties: these are not to be construed as specifications.
2Type I, 2.0 in/min
30.051 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.