Ketron PEEK 30% GF (EXTRUSION) Quadrant Polyetheretherketone (Glass Fiber Reinforcement, 30%)

Product Description

Extruded 30% Glass fiber reinforced polyetheretherketone. The addition of glass fibers significantly reduces the expansion rate and increases the flexural modulus of PEEK. This grade is ideal for structural applications that require improved strength, stiffness or stability, especially at temperatures above 300°F.

General

Material Status

Commercial: Active

Availability

North America

Filler / Reinforcement

Glass Fiber Reinforcement, 30% Filler by Weight

Features

Acid Resistant

Alcohol Resistant

Alkali Resistant

Good Abrasion Resistance

Good Chemical Resistance

Good Stability

Good Stiffness

Good Strength

Good Thermal Stability

Good Wear Resistance

Hydrocarbon Resistant

Hydrolytically Stable

Low to No Water Absorption

Salt Water/Spray Resistant

Solvent Resistant

Uses

Bearings

Bushings

General Purpose

Housings

Pump Parts

Sealing Devices

Seals

Structural Parts

Valves/Valve Parts

Forms

Customizable Forms

Preformed Parts

Profiles

Sheet

Tubing

Processing Method

Extrusion

Physical	Nominal Value	Unit	Test Method
Specific Gravity			ASTM D792
Water Absorption			ASTM D570
24 hr		%
Saturation		%
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus		psi	ASTM D638
Tensile Strength (Ultimate)		psi	ASTM D638
Tensile Elongation (Break)		%	ASTM D638
Flexural Modulus		psi	ASTM D790
Flexural Strength (Yield)		psi	ASTM D790
Compressive Modulus		psi	ASTM D695
Compressive Strength (10% Strain)		psi	ASTM D695
Shear Strength		psi	ASTM D732
Impact	Nominal Value	Unit	Test Method
Notched Izod Impact		ft·lb/in	ASTM D256A
Hardness	Nominal Value	Unit	Test Method
Rockwell Hardness			ASTM D785
M-Scale
R-Scale
Durometer Hardness (Shore D)			ASTM D2240
Thermal	Nominal Value	Unit	Test Method
Deflection Temperature Under Load (264 psi, Unannealed)		°F	ASTM D648
Maximum Use Temperature - Long Term, Air		°F
Peak Crystallization Temperature (DSC)		°F	ASTM D3418
CLTE - Flow² (-40 to 300°F)		in/in/°F	ASTM E831
Thermal Conductivity		Btu·in/hr/ft²/°F	ASTM F433
Electrical	Nominal Value	Unit	Test Method
Surface Resistivity³		ohms	Internal Method
Dielectric Strength⁴		V/mil	ASTM D149
Flammability	Nominal Value	Unit	Test Method
Flame Rating - UL (0.125 in, Estimated Rating)			UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Ketron® PEEK 30% GF, Ketron PEEK 30 GF, Ketron® PEEK 30% GF (EXTRUSION), Ketron PEEK 30 GF EXTRUSION, Ketron® , Ketron, KetronPEEK30GFEXTRUSION, PEEK 30% GF, PEEK 30 GF, PEEK30GF, PEEK 30% GF (EXTRUSION), PEEK 30 GF EXTRUSION, PEEK30, 30GF, GFEXTRUSION, PEEK30GFEXTRUSION, Polyetheretherketone, PEEK, Polyaryletherketone, PAEK, Quadrant, 30PEEK
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant, Good Wear Resistance, Wear Resistant, Good Thermal Stability, Low Water Absorption, Low Moisture Absorption, Water Resistant, Moisure Resistant, Good Abrasion Resistance, Abrasion Resistant, Salt Water Spray Resistant, Salt Water Resistant, Salt Spray Resistant, Good Stability, Good Stiffness, Good Strength.
Uses
Uses may also be described by the following terms: Housings, Housing, Valves, Valve Parts.

Notes

¹Typical properties: these are not to be construed as specifications.

²68°F

³EOS/ESD S11.11

⁴Method A (Short-Time)

Ketron® PEEK 30% GF (EXTRUSION)

Polyetheretherketone

Glass Fiber Reinforcement, 30%

Supplied by Quadrant Engineering Plastic Products