IDES Prospector Already have an account? Login Here

IDES

Ketron® PEEK 30% GF Compression

Polyetheretherketone

Glass Fiber Reinforcement, 30%

Supplied by Quadrant Engineering Plastic Products

The technical datasheet with complete property values for Ketron® PEEK 30% GF Compression is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Compression molded 30% Glass fiber reinforced polyetheretherketone. The addition of glass fibers significantly reduces the expansion rate and increases the flexural modulus of PEEK. This grade is ideal for structural applications that require improved strength, stiffness or stability, especially at temperatures above 300°F.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 30% Filler by Weight
Features 
  • Acid Resistant
  • Alcohol Resistant
  • Alkali Resistant
  • Good Abrasion Resistance
  • Good Chemical Resistance
  • Good Stability
  • Good Stiffness
  • Good Strength
  • Good Thermal Stability
  • Good Wear Resistance
  • Hydrocarbon Resistant
  • Hydrolytically Stable
  • Low Moisture Absorption
  • Solvent Resistant
Uses 
  • Bearings
  • Bushings
  • General Purpose
  • Housings
  • Pump Parts
  • Sealing Devices
  • Seals
  • Structural Parts
  • Valves/Valve Parts
Forms 
  • Customizable Forms
  • Disc
  • Preformed Parts
  • Rod
  • Tubing
Processing Method 
  • Compression Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Water Absorption
     ASTM D570
24 hr
%
  
Saturation
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength (Ultimate)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength (Yield)
psi
 ASTM D790
Compressive Modulus
psi
 ASTM D695
Compressive Strength (10% Strain)
psi
 ASTM D695
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256A
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness
     ASTM D785
M-Scale
 
  
R-Scale
 
  
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
Maximum Use Temperature - Long Term, Air
°F
  
Peak Crystallization Temperature (DSC)
°F
 ASTM D3418
CLTE - Flow 2 (-40 to 300°F)
in/in/°F
 ASTM E831
Thermal Conductivity
Btu·in/hr/ft²/°F
 ASTM F433
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity 3
ohms
 Internal Method
Dielectric Strength 4
V/mil
 ASTM D149
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.125 in, Estimated Rating)
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Ketron® PEEK 30% GF Compression, Ketron PEEK 30 GF Compression, Ketron® , Ketron, KetronPEEK30GFCompression, PEEK 30% GF Compression, PEEK 30 GF Compression, PEEK30, 30GF, GFCompression, PEEK30GFCompression, Polyetheretherketone, PEEK, Polyaryletherketone, PAEK, Quadrant, 30PEEK
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant, Good Wear Resistance, Wear Resistant, Good Thermal Stability, Low Moisture Absorption, Low Water Absorption, Water Resistant, Moisture Resistant, Good Abrasion Resistance, Abrasion Resistant, Good Stability, Good Stiffness, Good Strength.
Uses
Uses may also be described by the following terms: Valves, Valve Parts, Housings, Housing.
Notes
1Typical properties: these are not to be construed as specifications.
268°F
3EOS/ESD S11.11
4Method A (Short-Time)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.