IDES Prospector Already have an account? Login Here

IDES

Fluorel FG 5630Q

Fluoroelastomer

Supplied by Dyneon™ Fluoropolymers

The technical datasheet with complete property values for Fluorel FG 5630Q is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Product Features:
-In compliance with FDA 21 CFR 177.2600(c)(4)(i) and other applicable regulations for repeated food contact use.

-When Compared to diamine cured compounds, this product gives:
--Excellent mold release
--Better mold flow
--Better scorch safety
--Superior compression set resistance
--Superior water resistance at elevated temperatures
-Composition: di-polymer of vinylidene fluoride and hexafluoropropylene
-Cure technology: proprietary incorporated cure

Recommended Processing Procedure: Fluorel FG 5630Q can be compounded using standard water cooled internal mixers or two-roll mills. For food contact applications, fillers and ingredients utilized must be in compliance with applicable regulations for repeated food contact use. The "dry" ingredients should be blended before adding to the masticated gum. For best results, FG 5630Q should be banded on the mill several minutes prior to adding the blended dry ingredients. Once mixed, the compounded stocks display excellent processing safety and storage ability.

Product Form: FG 5630Q is packaged in slab form. Nominal size is 22" x 12" x 3". FG 5630Q is available in a bulk packaging system for 1,650 pounds of material. Smaller quantities are available in 55 pound boxes.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
  • North America
  
Features 
  • Acid Resistant
  • Food Contact Acceptable
  • Good Flow
  • Good Mold Release
  • Oil Resistant
  • Steam Resistant
Uses 
  • Gaskets
  • High Temperature Applications
  • Non-specific Food Applications
  • Pump Parts
  • Valves/Valve Parts
Agency Ratings 
Forms 
  • Pellets
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress (100% Strain)
psi
 ASTM D412
Tensile Strength (Break)
psi
 ASTM D412
Tensile Elongation (Break)
%
 ASTM D412
Compression Set (392°F)
%
 ASTM D395
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A)
 
 ASTM D2240
Additional Information
Retraction Temperature, ASTM D1329: 0.0°F (-18.0°C).
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Fluorel FG 5630Q, Fluorel FG , FluorelFG5630Q, FluorelFG, FG 5630 Q, FG5630Q, FG5630, FG, 5630 Q, 5630Q, Fluoroelastomer, Fluorelastomer, Fluoropolymer, Dyneon, Q5630, 5630FG
Features
Features may also be described by the following terms: Good Mold Release, Easy Release, Good Demolding, Good Flow.
Uses
Uses may also be described by the following terms: Food Applications, Valves, Valve Parts, Gaskets, Gasketing.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.