IDES Prospector Already have an account? Login Here

IDES

Modified Plastics MN 6/6-FG 10

Polyamide 66

Glass Fiber Reinforcement, 10%

Supplied by Modified Plastics, Inc.

The technical datasheet with complete property values for Modified Plastics MN 6/6-FG 10 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 10% Filler by Weight
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
ASTM D792
Molding Shrinkage - Flow
in/in
ASTM D955
Water Absorption
    ASTM D570
24 hr
%
 
Saturation
%
 
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield)
psi
ASTM D638
Tensile Elongation (Yield)
%
ASTM D638
Flexural Modulus
psi
ASTM D790
Flexural Strength (Yield)
psi
ASTM D790
Compressive Strength
psi
ASTM D695
Shear Strength
psi
ASTM D732
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F, 0.250 in)
ft·lb/in
ASTM D256
Unnotched Izod Impact (73°F, 0.250 in)
ft·lb/in
ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
    ASTM D648
66 psi, Unannealed
°F
 
264 psi, Unannealed
°F
 
Vicat Softening Temperature
°F
ASTM D1525
CLTE - Flow
in/in/°F
ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
ASTM D257
Dielectric Strength
V/mil
ASTM D149
Dielectric Constant
    ASTM D150
100 Hz
 
 
1 kHz
 
 
1 MHz
 
 
Dissipation Factor (1 kHz)
 
ASTM D150
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Modified Plastics MN 6/6-FG 10, Modified Plastics MN 66FG 10, Modified Plastics , ModifiedPlasticsMN66FG10, ModifiedPlastics, PlasticsMN 6 6 FG 10, MN 6, PlasticsMN 6/6-FG 10, PlasticsMN 66FG 10, PlasticsMN 6:6-FG 10, PlasticsMN 6+6-FG 10, PlasticsMN 6-6-FG 10, PlasticsMN 6_6-FG 10, PlasticsMN 6 6-FG 10, PlasticsMN 6/6:FG 10, PlasticsMN 6/6/FG 10, PlasticsMN 6/6+FG 10, PlasticsMN 6/6_FG 10, PlasticsMN 6/6 FG 10, PlasticsMN6, PlasticsMN 6, MN 6 6 FG 10, PlasticsMN66FG10, PlasticsMN 6_6FG 10, PlasticsMN 6 6FG 10, PlasticsMN 66_FG 10, PlasticsMN 66 FG 10, MN 6/6-FG 10, MN 66FG 10, MN 6:6-FG 10, MN 6+6-FG 10, MN 6-6-FG 10, MN 6_6-FG 10, MN 6 6-FG 10, MN 6/6:FG 10, MN 6/6/FG 10, MN 6/6+FG 10, MN 6/6_FG 10, MN 6/6 FG 10, MN6, 66, 6FG, FG10, PlasticsMN6_6FG10, PlasticsMN66_FG10, MN66FG10, MN 6_6FG 10, MN 6 6FG 10, MN 66_FG 10, MN 66 FG 10, MN6_6FG10, MN66_FG10, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Modified Plas, Polyamide66, Nylon66, 6MN, 6PlasticsMN
Generic Name
Generic Name may also be described by the following terms: PA66.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
 
Processing (Melt) Temp
°F
 
Mold Temperature
°F
 
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.