IDES Prospector Already have an account? Login Here

IDES

Modified Plastics MPP-S1

Polypropylene

Supplied by Modified Plastics, Inc.

The technical datasheet with complete property values for Modified Plastics MPP-S1 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Low to No Water Absorption
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow (0.125 in)
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield)
psi
 ASTM D638
Tensile Elongation (Yield)
%
 ASTM D638
Flexural Strength (Yield)
psi
 ASTM D790
Compressive Strength
psi
 ASTM D695
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F, 0.250 in)
ft·lb/in
 ASTM D256
Unnotched Izod Impact (73°F, 0.250 in)
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
CLTE - Flow
in/in/°F
 ASTM D696
Thermal Conductivity
Btu·in/hr/ft²/°F
 ASTM C177
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Dielectric Constant
 
 ASTM D150
Dissipation Factor
 
 ASTM D150
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Modified Plastics MPP-S1, Modified Plastics MPPS1, Modified Plastics , ModifiedPlasticsMPPS1, ModifiedPlastics, PlasticsMPP S 1, MPP, PlasticsMPP-S1, PlasticsMPPS1, PlasticsMPP:S1, PlasticsMPP/S1, PlasticsMPP+S1, PlasticsMPP_S1, PlasticsMPP S1, PlasticsMPPS, PlasticsMPP, MPP S 1, MPP-S1, MPPS1, MPP:S1, MPP/S1, MPP+S1, MPP_S1, MPP S1, MPPS, S1, Polypropylene, Unspecified, Polypropylene Unspecified, PP, Unspecified, PP Unspecified, Polypropylene, PP, Modified Plas, PolypropyleneUnspecified, PPUnspecified, SMPP, SPlasticsMPP
Generic Name
Generic Name may also be described by the following terms: Polypropilene, Polypropelene.
Features
Features may also be described by the following terms: Low Water Absorption, Low Moisture Absorption, Water Resistant, Moisure Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.