IDES Prospector Already have an account? Login Here

IDES

Custom Compounding CC503

Polytetrafluoroethylene

Mineral Filler, 15%

Supplied by Dyneon™ Fluoropolymers

The technical datasheet with complete property values for Custom Compounding CC503 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
  • North America
  
Filler / Reinforcement 
  • Mineral Filler, 15% Filler by Weight
Features 
  • Good Thermal Stability
  • Good Wear Resistance
  • Low Friction
Uses 
  • Bearings
  • Seals
  • Seats
Agency Ratings 
Appearance 
  • Colors Available
  • White
  
Forms 
  • Powder
Processing Method 
  • Extrusion
  • Sintering
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield, 73°F)
psi
 ASTM D638
Tensile Elongation (Yield, 73°F)
%
 ASTM D638
Flexural Strength (Yield, 73°F)
psi
 ASTM D790
Compressive Modulus
psi
 ASTM D695
Compressive Strength
psi
 ASTM D695
Coefficient of Friction
     ASTM D1894
vs. Itself - Dynamic
 
  
vs. Itself - Static
 
  
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
CLTE - Flow
in/in/°F
 ASTM D696
Additional Information
Tensile properties, ASTM D638, were tested according to ASTM D4745.
Durometer Hardness, ASTM D2240, 15 sec: 61 Shore D
Deformation Under Load, ASTM D621, 2000 psi (Initial), 70°F: 7.7%
Deformation Under Load, ASTM D621, 2000 psi (Perm), 70°F: 5.9%
Deformation Under Load, ASTM D621, 600 psi (Initial), 500°F: 14.2%
Deformation Under Load, ASTM D621, 600 psi (Perm), 500°F: 9.8%
Flexural Stress, ASTM D790: 15.7 lbs
Wear Factor, ASTM D3702, 5000 PV: 10E-10 in³-min/ft-lb-hr
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Custom Compounding CC503, Custom Compounding , CustomCompoundingCC503, CustomCompounding, CompoundingCC 503, CompoundingCC503, Compounding, CC 503, CC503, Polytetrafluoroethylene, PTFE, Fluoropolymer, Dyneon, 503CC, 503CompoundingCC
Features
Features may also be described by the following terms: Good Wear Resistance, Wear Resistant, Good Thermal Stability, Low Friction.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.