IDES Prospector Already have an account? Login Here

IDES

Elastollan® 1164D50

Thermoplastic Polyurethane Elastomer (Polyether)

Supplied by BASF Corp. Thermoplastic Polyurethanes

The technical datasheet with complete property values for Elastollan® 1164D50 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Elastollan® 1164D50 is a polyether-based thermoplastic polyurethane (TPU). It exhibits excellent abrasion resistance, toughness, transparency, low temperature properties, hydrolytic stability, and fungus resistance. Elastollan® 1164D50 is conforming to the FDA food contact section, book 21, section 177.2600. As with all TPU products, Elastollan® 1164D50 must be dried before processing. The drying step is required to maintain a low moisture content until the product enters the processing equipment. The water content must be less than 0.03% before and during processing. The typical drying conditions should be 2-4 hours @ 195°-220°F (90°-105°C). Elastollan® 1164D50 can be stored for up to 1 year in its original container. Containers should be stored in a cool and dry area.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Fungus Resistant
  • Good Abrasion Resistance
  • Good Toughness
  • Hydrolytically Stable
  
Agency Ratings 
Appearance 
  • Clear/Transparent
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Taber Abrasion Resistance (1000 g, H-18 Wheel)
mg
 ASTM D1044
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress
     ASTM D412
100% Strain
psi
  
300% Strain
psi
  
Tensile Strength (Break)
psi
 ASTM D412
Tensile Elongation (Break)
%
 ASTM D412
Elongation Set After Break
%
 ASTM D412
Tear Strength 2
lbf/in
 ASTM D624
Compression Set
     ASTM D395B
73°F, 22.0 hr
%
  
158°F, 22.0 hr
%
  
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Additional Information
The value listed as Tensile Modulus ASTM 638, was tested in accordance with E-Modulus ASTM D412.
Related Terminology
This supplier and product may also be known by these terms: Elastolan, Ellastolan

Product names can be difficult to match. You may have searched any one of these terms to find this product: Elastollan® 1164D50, Elastollan 1164D50, Elastollan® , Elastollan, Elastollan1164D50, 1164 D 50, 1164D50, 1164D, D50, Thermoplastic Polyurethane Elastomer, Thermoplastic Polyurethane Elastomer (Polyether), Thermoplastic Polyurethane Elastomer Polyether, TPU-Polyether, TPUPolyether, TPU:Polyether, TPU/Polyether, TPU+Polyether, TPU_Polyether, TPU Polyether, Thermoplastic Polyurethane, TPU, BASF TPU, ThermoplasticPolyurethaneElastomerPolyether, ThermoplasticPolyurethane, D1164
Features
Features may also be described by the following terms: Good Abrasion Resistance, Abrasion Resistant, Good Toughness, Tough.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Processing (Melt) Temp
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Die C
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.