|
Density
|
|
g/cm³
|
ISO 1183 |
|
Melt Volume-Flow Rate (MVR) (220°C/10.0 kg)
|
|
in³/10min
|
ISO 1133 |
|
Molding Shrinkage - Flow
|
|
%
|
ISO 294-4 |
|
Water Absorption
|
|
|
ISO 62 |
|
73°F, 24 hr
|
|
%
|
|
|
Saturation, 73°F
|
|
%
|
|
|
Equilibrium, 73°F, 50% RH
|
|
%
|
|
|
Tensile Modulus (73°F)
|
|
psi
|
ISO 527-2 |
|
Tensile Stress (Yield, 73°F)
|
|
psi
|
ISO 527-2/50 |
|
Tensile Strain (Yield, 73°F)
|
|
%
|
ISO 527-2/50 |
|
Nominal Tensile Strain at Break (73°F)
|
|
%
|
ISO 527-2/50 |
|
Tensile Creep Modulus (1000 hr)
|
|
psi
|
ISO 899-1 |
|
Flexural Strength (73°F)
|
|
psi
|
ISO 178 |
|
Shear Modulus (73°F)
|
|
psi
|
ISO 537 |
|
Charpy Notched Impact Strength
|
|
|
ISO 179/1eA |
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
|
Charpy Unnotched Impact Strength
|
|
|
ISO 179/1eU |
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
|
Notched Izod Impact (73°F)
|
|
ft·lb/in
|
ASTM D256A |
|
Ball Indentation Hardness (H 358/30)
|
|
psi
|
ISO 2039-1 |
|
Heat Deflection Temperature
|
|
|
|
|
66 psi, Unannealed
|
|
°F
|
ISO 75-2/B |
|
264 psi, Unannealed
|
|
°F
|
ISO 75-2/A |
|
Vicat Softening Temperature
|
|
|
|
|
--
|
|
°F
|
ISO 306/A50 |
|
--
|
|
°F
|
ISO 306/B50 |
|
CLTE - Flow (73 to 176°F)
|
|
in/in/°F
|
ISO 11359-2 |
|
Thermal Conductivity
|
|
Btu·in/hr/ft²/°F
|
ISO 8302 |
|
Surface Resistivity
|
|
ohm
|
IEC 60093 |
|
Volume Resistivity
|
|
ohm·cm
|
IEC 60093 |
|
Relative Permittivity
|
|
|
IEC 60250 |
|
73°F, 100 Hz
|
|
|
|
|
73°F, 1 MHz
|
|
|
|
|
Dissipation Factor
|
|
|
IEC 60250 |
|
73°F, 100 Hz
|
|
|
|
|
73°F, 1 MHz
|
|
|
|
|
Comparative Tracking Index (Solution A)
|
|
V
|
IEC 60112 |
|
Electric Strength
|
|
V/mil
|
IEC 60243-1 |
|
Flame Rating - UL (0.0630 in)
|
|
|
UL 94 |
|
The value listed as Thermal Conductivity, ISO 8302, was tested in accordance with DIN 52612-2.
Flammability by electrical sources of ignition, IEC 60707, Method BH, 4mm: HB
Maximum Service Temperature (Short Cycle Operation): 80°C
|
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Luran® S 797 S, Luran S 797 S, Luran® S , Luran S, LuranS797S, LuranS, S 797 S, S797 S, S797S, 797 S, 797S, Acrylonitrile Styrene Acrylate, ASA, Styrolution, AcrylonitrileStyreneAcrylate, S797
|
|
Features may also be described by the following terms: High Impact Resistance.
|
|
Uses may also be described by the following terms: Housings, Housing.
|
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1).
|