IDES Prospector Already have an account? Login Here

IDES

WPP TPO TPO-5674

Compounded Polypropylene

Supplied by Washington Penn Plastic Co. Inc.

The technical datasheet with complete property values for WPP TPO TPO-5674 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
TPO-5674 is an olefin alloy with medium rigidity. This material is used for a variety of automotive applications. Additional products are offered with properties tailored for specific applications. This grade features medium flow, good low temperature impact, very good ductility and practical toughness, and an excellent balance of impact strength and rigidity. Typical applications include air ducts, rocker panels, license plate brackets, and other various automotive applications.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Ductile
  • Good Toughness
  • Good Wear Resistance
  • High Rigidity
  • High Strength
  • Low Temperature Impact Resistance
  • Medium Flow
  • Scratch Resistant
Uses 
  • Automotive Applications
Automotive Specifications 
Appearance 
  • Colors Available
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (Yield)
psi
 ASTM D638
Tensile Elongation 2 (Break)
%
 ASTM D638
Flexural Modulus - Tangent 3
psi
 ASTM D790
Flexural Strength 3
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Instrumented Dart Impact (-22°F)
in·lb
 ASTM D3763
Gardner Impact (-22°F)
in·lb
 ASTM D3029
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness
     ASTM D2240
Shore A
 
  
Shore D
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: WPP TPO TPO-5674, WPP TPO TPO5674, WPP TPO , WPPTPOTPO5674, WPPTPO, TPO, TPOTPO-5674, TPOTPO5674, TPOTPO:5674, TPOTPO/5674, TPOTPO+5674, TPOTPO_5674, TPOTPO 5674, TPOTPO, TPO-5674, TPO5674, TPO:5674, TPO/5674, TPO+5674, TPO_5674, TPO 5674, Polypropylene, Compounded, Polypropylene Compounded, Polypropylene, PP, Washington Penn, PolypropyleneCompounded, 5674TPO, 5674TPOTPO
Features
Features may also be described by the following terms: High Rigidity, Medium Flow, Medium Melt, Medium MFI, Low Temperatuer Impact Resistance, Low Temp Impact Resistance, Good Toughness, Tough, High Strength, Good Wear Resistance, Wear Resistant, Scratch Resistant, Resists Scratches.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Automotive Specifications
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Holding Pressure
psi
  
Back Pressure
psi
  
Clamp Tonnage
tons/in²
  
Cushion
in
  
Injection Notes
Injection Speed: 0.25 to 2.5 in/s
Zone 4 Temperature: 420 to 445°F
Hot Runner Temperature: 420 to 460°F
Hydraulic Oil Temperature: 110 to 125°F
Shot Capacity vs. Barrel Capacity: 2.5 to 4
Screw Decompression: 0.1 to 0.25 in
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
30.050 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.