IDES Prospector Already have an account? Login Here

IDES

WPP TPO TPO-5674 P Black

Compounded Polypropylene

Mineral Filler

Supplied by Washington Penn Plastic Co. Inc.

The technical datasheet with complete property values for WPP TPO TPO-5674 P Black is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Mineral Filler
Features 
  • Ductile
  • Good Impact Resistance
  • Good Toughness
  • Medium Flow
  • Medium Rigidity
Uses 
  • Automotive Applications
  • Automotive Exterior Parts
  
Automotive Specifications 
Appearance 
  • Black
  • Colors Available
  
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 ISO 527-2/50
Flexural Modulus 2
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Instrumented Dart Impact 3
     ASTM D3763
-22°F, Energy at Peak Load
in·lb
  
73°F, Energy at Peak Load
in·lb
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: WPP TPO TPO-5674 P Black, WPP TPO TPO5674 P Black, WPP TPO , WPPTPOTPO5674PBlack, WPPTPO, TPO, TPOTPO-5674 P Black, TPOTPO5674 P Black, TPOTPO:5674 P Black, TPOTPO/5674 P Black, TPOTPO+5674 P Black, TPOTPO_5674 P Black, TPOTPO 5674 P Black, TPOTPO5674, TPOTPO, TPOTPO5674PBlack, TPO-5674 P Black, TPO5674 P Black, TPO:5674 P Black, TPO/5674 P Black, TPO+5674 P Black, TPO_5674 P Black, TPO 5674 P Black, TPO5674, 5674P, PBlack, TPOTPO_5674PBlack, TPO5674PBlack, TPO_5674PBlack, Polypropylene, Compounded, Polypropylene Compounded, Polypropylene, PP, Washington Penn, PolypropyleneCompounded, 5674TPO, 5674TPOTPO
Features
Features may also be described by the following terms: Good Toughness, Tough, Medium Rigidity, Good Rigidity, Medium Flow, Medium Melt, Medium MFI, Good Impact Resistance.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Automotive Specifications
This plastic material has approval for 3 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (1), GM (2).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Holding Pressure
psi
  
Back Pressure
psi
  
Clamp Tonnage
tons/in²
  
Cushion
in
  
Injection Notes
Injection Speed: 0.25 to 2.5 in/s
Zone 4 Temperature: 420 to 445°F
Hot Runner Temperature: 420 to 460°F
Hydraulic Oil Temperature: 110 to 125°F
Shot Capacity vs. Barrel Capacity: 2.5 to 4
Screw Decompression: 0.1 to 0.25 in
Notes
1Typical properties: these are not to be construed as specifications.
20.079 in/min
37.22 ft/sec
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.