NORYL 725A Resin SABIC IP Euro Polyphenylene Ether + PS

Product Description
NORYL 725A is an unfilled material, with a Vicat B/120 of 135°C according ISO 306. NORYL 725A has been designed for use in automotive interior applications, where anti-squeak is required.
General
Material Status	Commercial: Active
Availability	Europe
Uses	Automotive Interior Parts
RoHS Compliance
Automotive Specifications
Processing Method	Injection Molding

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ISO 1183
Melt Volume-Flow Rate (MVR) (280°C/5.0 kg)		in³/10min	ISO 1133
Molding Shrinkage - Flow²		in/in	Internal Method
Water Absorption			ISO 62
Saturation, 73°F		%
Equilibrium, 73°F, 50% RH		%
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus		psi	ISO 527-2/1
Tensile Stress			ISO 527-2/50
Yield		psi
Break		psi
Tensile Strain			ISO 527-2/50
Yield		%
Break		%
Flexural Modulus³		psi	ISO 178
Flexural Strength^3, 4		psi	ISO 178
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel)		mg	Internal Method
Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength⁵			ISO 179/1eA
-22°F		ft·lb/in²
73°F		ft·lb/in²
Notched Izod Impact Strength⁶			ISO 180/1A
-22°F		ft·lb/in²
73°F		ft·lb/in²
Hardness	Nominal Value	Unit	Test Method
Ball Indentation Hardness (H 358/30)		psi	ISO 2039-1
Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature⁷
66 psi, Unannealed, 3.94 in Span		°F	ISO 75-2/Be
264 psi, Unannealed, 3.94 in Span		°F	ISO 75-2/Ae
Vicat Softening Temperature
--		°F	ISO 306/A50
--		°F	ISO 306/B50
--		°F	ISO 306/B120
Ball Pressure Test (167°F)			IEC 60695-10-2
CLTE			ISO 11359-2
Flow: 73 to 176°F		in/in/°F
Transverse: 73 to 176°F		in/in/°F
Thermal Conductivity		Btu·in/hr/ft²/°F	ISO 8302
Electrical	Nominal Value	Unit	Test Method
Surface Resistivity		ohms	IEC 60093
Volume Resistivity		ohm·cm	IEC 60093
Relative Permittivity			IEC 60250
50 Hz
60 Hz
1 MHz
Dissipation Factor			IEC 60250
50 Hz
60 Hz
1 MHz
Comparative Tracking Index		V	IEC 60112
Electric Strength (0.126 in, in Oil)		V/mil	IEC 60243-1
Flammability	Nominal Value	Unit	Test Method
Flame Rating - UL (0.0630 in, Testing by SABIC)			UL 94
Glow Wire Flammability Index (0.126 in)		°F	IEC 60695-2-12
Oxygen Index		%	ISO 4589-2
Related Terminology
This supplier and product may also be known by these terms: GE Plastics Europe, LNP Engineering Plastics, GE Polymerland Europe, GE Polymerland, GE Plastics Product names can be difficult to match. You may have searched any one of these terms to find this product: NORYL* 725A Resin, NORYL 725A Resin, NORYL* , NORYL, NORYL725AResin, 725 A Resin, 725A Resin, 725A, AResin, 725AResin, Polyphenylene Ether + PS, Polyphenylene Ether PS, Polyphenylene Ether : PS, Polyphenylene Ether / PS, Polyphenylene Ether - PS, Polyphenylene Ether _ PS, Polyphenylene Ether PS, PPE+PS, PPEPS, PPE:PS, PPE/PS, PPE-PS, PPE_PS, PPE PS, Polyphenylene Ether, PPE, SABIC IP Euro, PolyphenyleneEtherPS, PolyphenyleneEther, PolyphenyleneEther_PS, A725
Generic Name
Generic Name may also be described by the following terms: PPO.
Automotive Specifications
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): VAG (1).

Injection	Nominal Value	Unit
Drying Temperature		°F
Drying Time		hr
Hopper Temperature		°F
Rear Temperature		°F
Middle Temperature		°F
Front Temperature		°F
Nozzle Temperature		°F
Processing (Melt) Temp		°F
Mold Temperature		°F

Notes

¹Typical properties: these are not to be construed as specifications.

²Tensile Bar

³0.079 in/min

⁴Yield

⁵80*10*4 sp=62mm

⁶80*10*4

⁷120*10*4 mm

NORYL* 725A Resin

Polyphenylene Ether + PS

Supplied by SABIC Innovative Plastics Europe