IDES Prospector Already have an account? Login Here

IDES

Daplen™ BH5363

Low Density Polyethylene

Supplied by Borealis AG

The technical datasheet with complete property values for Daplen™ BH5363 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
  • North America
  
Features 
  • Good Chemical Resistance
  • High ESCR (Stress Crack Resist.)
  • High Molecular Weight
Uses 
  • Containers
Forms 
  • Granules
Processing Method 
  • Blow Molding
  • Extrusion
  • Film Extrusion
Multi-Point Data 
  • Viscosity vs. Shear Rate (ISO 11403-2)
Physical
Nominal Value
Unit
Test Method
Density      
--
g/cm³
 ISO 1183
--
lb/in³
 ISO 1183 2
Melt Mass-Flow Rate (MFR) (190°C/21.6 kg)
g/10 min
 ISO 1133
Melt volume-flow rate (190°C/5.0 kg)
in³/10min
 ISO 1133 2
Environmental Stress-Cracking Resistance (10% Antarox, F50)
hr
 ASTM D1693
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1, ISO 527-2 2
Tensile Stress (Yield)
psi
 ISO 527-2/50, ISO 527-2 2
Tensile Strain (Yield)
%
 ISO 527-2/50, ISO 527-2 2
Nominal strain at break
%
 ISO 527-2 2
Flexural Modulus 3
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy notched impact strength (73°F)
ft·lb/in²
 ISO 179/1eA 2
Charpy impact strength (73°F)
 
 ISO 179/1eU 2
Tensile notched impact strength (73°F)
ft·lb/in²
 ISO 8256/1 2
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore D)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi
°F
 ISO 75-2 2
Vicat Softening Temperature (50°C/h, B (50N))
°F
 ISO 306 2
Melting Temperature 4
°F
 ISO 11357-3 2
Electrical
Nominal Value
Unit
Test Method
Surface resistivity
ohms
 IEC 60093 2
Volume resistivity
ohm·in
 IEC 60093 2
Relative Permittivity     IEC 60250 2
100 Hz
 
  
1 MHz
 
  
Dissipation Factor     IEC 60250 2
100 Hz
 
  
1 MHz
 
  
Electric strength
V/mil
 IEC 60243-1 2
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Daplen™ BH5363, Daplen BH5363, Daplen™ , Daplen, DaplenBH5363, BH 5363, BH5363, Polyethylene, Low Density, Polyethylene Low Density, LDPE, Polyethylene, PE, Borealis, PolyethyleneLowDensity, 5363BH
Features
Features may also be described by the following terms: High Molecular Weight, High MW, Good Chemical Resistance, Chemical Resistant, High Environmental Stress Cracking Resistance, High ESCR, Stress Cracking Resistant.
Extrusion
Nominal Value
Unit
 
Cylinder Zone 3 Temp.
°F
  
Melt Temperature
°F
  
Die Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted.
30.039 in/min
418 °F/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.