IDES Prospector Already have an account? Login Here

IDES

Clariant ABS ABS6200

Acrylonitrile Butadiene Styrene

Supplied by Clariant Performance Plastics

The technical datasheet with complete property values for Clariant ABS ABS6200 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Good Chemical Resistance
  • Good Dimensional Stability
  • High Gloss
  • High Impact Resistance
  
Uses 
  • Automotive Applications
Appearance 
  • Black
  • Colors Available
  • Natural Color
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield)
psi
 ASTM D638
Tensile Elongation (Yield)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.125 in)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Additional Information
Notched Izod Impact, ASTM D256, Colors: 6.3 ft-lb/in
Notched Izod Impact, ASTM D256, Black: 6.0 ft-lb/in
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Clariant ABS ABS6200, Clariant ABS , ClariantABSABS6200, ClariantABS, ABSABS 6200, ABSABS6200, ABS, ABS 6200, ABS6200, Acrylonitrile Butadiene Styrene, Clariant Perf, AcrylonitrileButadieneStyrene, 6200ABS, 6200ABSABS
Features
Features may also be described by the following terms: High Impact Resistance, Good Chemical Resistance, Chemical Resistant, Good Dimensional Stability, Dimensionally Stable, High Gloss.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Melt Temperature (Aim)
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Back Pressure
psi
  
Screw Speed
rpm
  
Cushion
in
  
Injection Notes
The minimum injection pressure to achieve 95% fill of the part during the boost injection pressure phase should be used. The hold pressure should be between 30% and 75% of the initial injection pressure.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.