IDES Prospector Already have an account? Login Here

IDES

Unifill-60 20-HDPE

High Density Polyethylene

Wood Flour, 20%

Supplied by North Wood Plastics, Inc.

The technical datasheet with complete property values for Unifill-60 20-HDPE is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Unifill-60 is a general purpose polyolefin compound compatible in both PP and HDPE. It is a masterbatch with 60% high quality pine wood flour filler. Made using only the highest quality melt filtered recycled resins, Unfill-60 is intended for cost sensitive applications where consistent color and performance are still critical. Unifill-60 can be used in many molding and extrusion applications for enhanced stiffness, reduced thermal expansion, at the same time retaining good Izod impact. Unifill-60 can be used in the following processes: High pressure injection molding, structural foam molding, blow molding, sheet extrusion for flat panels and thermoforming, and compression molding.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Wood Flour, 20% Filler by Weight
Recycled Content 
  • Yes, 13%
Features 
  • Good Stiffness
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength (Yield)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Unnotched Izod Impact
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Unifill-60 20-HDPE, Unifill60 20HDPE, Unifill-60 , Unifill60, Unifill:60, Unifill/60, Unifill+60, Unifill_60, Unifill 60, Unifill6020HDPE, 20, 20-HDPE, 20HDPE, 20:HDPE, 20/HDPE, 20+HDPE, 20_HDPE, 20 HDPE, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, North Wood, PolyethyleneHighDensity, HDPE20
Features
Features may also be described by the following terms: Good Stiffness.
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.