IDES Prospector Already have an account? Login Here

IDES

Orgalloy® RS 60E10

Polyamide 6 Alloy

Supplied by Arkema

The technical datasheet with complete property values for Orgalloy® RS 60E10 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Additive 
  • Impact Modifier
Features 
  • High Heat Resistance
  • Impact Modified
  • Platable
Forms 
  • Pellets
Processing Method 
  • Blow Molding
  • Calendering
  • Casting
  • Coating
  • Extrusion
  • Film Extrusion
  • Injection Molding
  • Profile Extrusion
  • Resin Transfer Molding
  • Sheet Extrusion
  • Thermoforming
Multi-Point Data 
  • Shear Modulus vs. Temperature (ISO 11403-1)
  • Viscosity vs. Shear Rate (ISO 11403-2)
  
Physical
Dry
Conditioned
Unit
Test Method
Density
lb/in³
 ISO 1183 2
Melt volume-flow rate (235°C/5.0 kg)
--
in³/10min
 ISO 1133 2
Water Absorption
       ISO 62 2
Saturation
--
%
  
Equilibrium
--
%
  
Mechanical
Dry
Conditioned
Unit
Test Method
Tensile modulus
--
psi
 ISO 527-2 2
Tensile Stress (Yield)
--
psi
 ISO 527-2 2
Tensile Strain (Yield)
--
%
 ISO 527-2 2
Nominal strain at break
--
%
 ISO 527-2 2
Thermal
Dry
Conditioned
Unit
Test Method
Deflection Temperature Under Load
       ISO 75-2 2
66 psi
--
°F
  
264 psi
--
°F
  
Melting Temperature 3
--
°F
 ISO 11357-3 2
CLTE
       ISO 11359-2 2
Flow
--
in/in/°F
  
Transverse
--
in/in/°F
  
Electrical
Dry
Conditioned
Unit
Test Method
Surface resistivity
--
ohm
 IEC 60093 2
Volume resistivity
--
ohm·in
 IEC 60093 2
Relative Permittivity
       IEC 60250 2
100 Hz
--
 
  
1 MHz
--
 
  
Dissipation Factor
       IEC 60250 2
100 Hz
--
 
  
1 MHz
--
 
  
Comparative tracking index
--
 
 IEC 60112 2
Electric strength
V/mil
 IEC 60243-1 2
Flammability
Dry
Conditioned
Unit
Test Method
Burning Behav. at 1.6mm nom. thickn. (0.06 in)
--
 
 ISO 1210 2
Burning Behav. at thickness h (0.126 in)
--
 
 ISO 1210 2
Related Terminology
Dry
Product names can be difficult to match. You may have searched any one of these terms to find this product: Orgalloy® RS 60E10, Orgalloy RS 60E10, Orgalloy® , Orgalloy, OrgalloyRS60E10, RS 60 E 10, RS 60E10, RS60, 60E, E10, RS60E10, Polyamide 6 Alloy, Nylon 6 Alloy, Polyamide, Nylon, Arkema, Polyamide6Alloy, Nylon6Alloy, 60RS
Features
Dry
Features may also be described by the following terms: High Heat Resistance.
Conditioned
Product names can be difficult to match. You may have searched any one of these terms to find this product: Orgalloy® RS 60E10, Orgalloy RS 60E10, Orgalloy® , Orgalloy, OrgalloyRS60E10, RS 60 E 10, RS 60E10, RS60, 60E, E10, RS60E10, Polyamide 6 Alloy, Nylon 6 Alloy, Polyamide, Nylon, Arkema, Polyamide6Alloy, Nylon6Alloy, 60RS
Notes
1Typical properties: these are not to be construed as specifications.
2Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted.
318 °F/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.