IDES Prospector Already have an account? Login Here

IDES

Surlyn® 1601-2LM

Ionomer

Supplied by DuPont Packaging & Industrial Polymers

The technical datasheet with complete property values for Surlyn® 1601-2LM is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Surlyn® 1601-2LM is available for use in conventional blown, cast film, and sheet extrusion equipment. It is also used in coextrusion equipment designed to process polyethylene and ethylene copolymer type resins.

Lower moisture specification for higher temperature processing
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Uses 
  • Cast Film
  • Film
  • Sheet
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Blown Film
  • Cast Film
  • Coextrusion
  • Sheet Extrusion
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238, ISO 1133
Ion Type
 
  
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ASTM D1525, ISO 306
Peak Melting Temperature
°F
 ASTM D3417, ISO 3146
Freezing Point
°F
 ASTM D3417
Related Terminology
This supplier and product may also be known by these terms: Surlin

Product names can be difficult to match. You may have searched any one of these terms to find this product: Surlyn® 1601-2LM, Surlyn 16012LM, Surlyn® , Surlyn, Surlyn16012LM, 1601, 1601 2 LM, 1601-2LM, 16012LM, 1601:2LM, 1601/2LM, 1601+2LM, 1601_2LM, 1601 2LM, 16012, 2LM, Ionomer, DuPont P&IP, 21601
Uses
Uses may also be described by the following terms: Cast Film.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Adapter Temperature
°F
  
Melt Temperature
°F
  
Die Temperature
°F
  
Extrusion Notes
The above processing values are for blown film.
Cast film parameters:
  • Feed Zone: 160°C
  • Second Zone: 210°C
  • Third Zone: 235°C
  • Fourth Zone: 235°C
  • Fifth Zone: 235°C
  • Adapter Zone: 235°C
  • Die Zone: 235°C
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.