IDES Prospector Already have an account? Login Here

IDES

Oleform SS03X

Polypropylene

Mineral Filler

Supplied by Chisso America Inc.

The technical datasheet with complete property values for Oleform SS03X is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Mineral Filler
Features 
  • Good Stiffness
  • High Gloss
  
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (Yield)
psi
 ASTM D638
Tensile Elongation 2 (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (66 psi, Unannealed)
°F
 ASTM D648
Vicat Softening Temperature
°F
 ASTM D1525
CLTE - Flow (-4 to 158°F)
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength (0.0394 in)
V/mil
 ASTM D149
Dielectric Constant (1 kHz)
 
 ASTM D150
Dissipation Factor (1 kHz)
 
 ASTM D150
Arc Resistance
sec
 ASTM D495
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0413 in, ALL)
 
 UL 94
UL File Number
 
  
Additional Information
Mold Shrinkage, Standard Value, 200 to 280°C Injection Temp., 2 to 3 mm Thickness: 1.4%
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Oleform SS03X, Oleform , OleformSS03X, SS 03 X, SS03X, SS03, 03X, Polypropylene, Unspecified, Polypropylene Unspecified, PP, Unspecified, PP Unspecified, Polypropylene, PP, Chisso, PolypropyleneUnspecified, PPUnspecified, 03SS
Generic Name
Generic Name may also be described by the following terms: Polypropilene, Polypropelene.
Features
Features may also be described by the following terms: High Gloss, Good Stiffness.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.