IDES Prospector Already have an account? Login Here

IDES

TECHNYL® C 216T

Polyamide 6

Supplied by Rhodia Engineering Plastics SA

The technical datasheet with complete property values for TECHNYL® C 216T is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
The good mechanical properties and the high transparency till 2-2.5 mm of thickness make it adequate for applications which request transparency at low thickness, such as:
  • fuel filters, brake fluid containers, ect.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Uses 
  • Automotive Applications
  • Containers
  
Appearance 
  • Clear/Transparent
  • Natural Color
  
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Dry
Conditioned
Unit
Test Method
Density
--
g/cm³
 ISO 1183
Molding Shrinkage
       ISO 294-4
Across Flow
--
%
  
Flow
--
%
  
Water Absorption (73°F, 24 hr)
--
%
 ISO 62
Mechanical
Dry
Conditioned
Unit
Test Method
Tensile Modulus (73°F)
psi
 ISO 527-2
Tensile Stress (Yield, 73°F)
psi
 ISO 527-2
Nominal Tensile Strain at Break (73°F)
%
 ISO 527-2
Flexural Modulus (73°F)
psi
 ISO 178
Flexural Strength (73°F)
psi
 ISO 178
Impact
Dry
Conditioned
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Charpy Unnotched Impact Strength (73°F)
 
 ISO 179/1eU
Notched Izod Impact Strength (73°F)
ft·lb/in²
 ISO 180
Thermal
Dry
Conditioned
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
--
°F
 ISO 75-2/A
Melting Temperature (DSC)
--
°F
 ISO 3146
CLTE - Flow (73 to 185°F)
--
in/in/°F
 ASTM E831
Electrical
Dry
Conditioned
Unit
Test Method
Surface Resistivity
ohm
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Relative Permittivity (1 MHz)
 
 IEC 60250
Dissipation Factor (1 MHz)
 
 IEC 60250
Comparative Tracking Index (Solution A)
--
V
 IEC 60112
Electric Strength
--
V/mil
 IEC 60243-1
Additional Information
Dry
Mold Shrinkage, RHODIA-EP, 23°C, Flow: 0.6 %
Mold Shrinkage, RHODIA-EP, 23°C, Across Flow: 0.8 %
Related Terminology
Dry
Product names can be difficult to match. You may have searched any one of these terms to find this product: TECHNYL® C 216T, TECHNYL C 216T, TECHNYL® C , TECHNYL C, TECHNYLC216T, TECHNYLC, C 216 T, C216T, C216, 216 T, 216T, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, Rhodia, Polyamide6, Nylon6, T216, 216C
Generic Name
Dry
Generic Name may also be described by the following terms: PA6.
Conditioned
Generic Name may also be described by the following terms: PA6.
Uses
Dry
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Conditioned
Product names can be difficult to match. You may have searched any one of these terms to find this product: TECHNYL® C 216T, TECHNYL C 216T, TECHNYL® C , TECHNYL C, TECHNYLC216T, TECHNYLC, C 216 T, C216T, C216, 216 T, 216T, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, Rhodia, Polyamide6, Nylon6, T216, 216C
Injection
Dry
Unit
 
Drying Temperature
°F
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.