IDES Prospector Already have an account? Login Here

IDES

K-Resin® SBC DK13

Styrene Butadiene Block Copolymer

Supplied by Chevron Phillips Chemical Company LLC

The technical datasheet with complete property values for K-Resin® SBC DK13 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Features 
  • Food Contact Acceptable
  • Good Heat Seal
  • Good Processability
  • Good Stiffness
  • Good Tear Strength
  • Good Toughness
  • High Clarity
  • High Gloss
Uses 
  • Film
  • Food Packaging
  • Medical Packaging
  • Shrink Wrap
  
Agency Ratings 
Appearance 
  • Clear/Transparent
Forms 
  • Pellets
Processing Method 
  • Blown Film
  • Cast Film
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (200°C/5.0 kg)
g/10 min
 ASTM D1238
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Film Puncture Energy
in·lb
  
Secant Modulus
     ASTM D882
1% Secant, MD
psi
  
1% Secant, TD
psi
  
Tensile Strength
     ASTM D882
MD: Yield
psi
  
TD: Yield
psi
  
Tensile Elongation
     ASTM D882
MD: Break
%
  
TD: Break
%
  
Dart Drop Impact
g
 ASTM D1709
Elmendorf Tear Strength
     ASTM D1922
MD
g
  
TD
g
  
Oxygen Permeability
cm³·mil/100in²/atm/24 hr
 ASTM D3985
Water Vapor Transmission
g/100 in²/24 hr
 ASTM E96
Impact
Nominal Value
Unit
Test Method
Instrumented Dart Impact
in·lb
 ASTM D3763
Optical
Nominal Value
Unit
Test Method
Gloss
 
 ASTM D2457
Transmittance
%
 ASTM D1003
Haze
%
 ASTM D1003
Additional Information
Shrinkage, ASTM D2732, MD, 300°F, 10 sec: 40%
Shrinkage, ASTM D2732, TD, 300°F, 10 sec: 36%

Crease Retention, TAPPI T446-B: 100%
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: K-Resin® SBC DK13, KResin SBC DK13, K-Resin® SBC , KResin SBC, K:Resin® SBC, K/Resin® SBC, K+Resin® SBC, K_Resin® SBC, K Resin® SBC, KResinSBCDK13, KResinSBC, K_Resin SBC, K Resin SBC, SBCDK 13, K_ResinSBC, SBCDK13, SBC, DK 13, DK13, Styrene Butadiene Block Copolymer, Thermoplastic Elastomer, TPE, sb, CP Chem, StyreneButadieneBlockCopolymer, ThermoplasticElastomer, 13DK, 13SBCDK
Features
Features may also be described by the following terms: Good Processability, Easy Processing, High Clarity, High Gloss, Good Heat Seal, Good Toughness, Tough, Good Stiffness, Good Tear Strength.
Uses
Uses may also be described by the following terms: Medical Packaging, Food Packaging, Shrink Wrap.
Agency Ratings
This plastic material has 3 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EEC (1), FDA (1), USP (1).
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.