IDES Prospector Already have an account? Login Here

IDES

Meldin® 2030

Thermoset Polyimide

Supplied by Saint Gobain Performance Plastics

The technical datasheet with complete property values for Meldin® 2030 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
The MELDIN® 2030 bearing compound operates with extremely low friction in both dynamic and static applications, and provides thermal and electrical insulation.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Additive 
  • PTFE Lubricant (300000 ppm)
Features 
  • Flame Retardant
  • Good Creep Resistance
  • Good Dimensional Stability
  • Good Wear Resistance
  • High Strength
  • High Temperature Strength
  • Low Friction
  • Lubricated
Uses 
  • Insulation
Forms 
  • Customizable Forms
Processing Method 
  • Compression Molding
  • Machining
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
     ASTM D638
--
psi
  
500°F
psi
  
600°F
psi
  
Tensile Strength
     ASTM D638
Break
psi
  
Break, 500°F
psi
  
Break, 600°F
psi
  
Tensile Elongation
     ASTM D638
Break
%
  
Break, 500°F
%
  
Break, 600°F
%
  
Flexural Modulus
psi
 ASTM D790
Flexural Strength (Break)
psi
 ASTM D790
Compressive Modulus
psi
 ASTM D695
Compressive Strength
     ASTM D695
10% Strain
psi
  
100% Strain, 600°F
psi
  
100% Strain, 500°F
psi
  
100% Strain
psi
  
Deformation Under Load
%
 ASTM D621
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
CLTE - Flow
in/in/°F
 ASTM D696
Thermal Conductivity
Btu·in/hr/ft²/°F
 ASTM C177
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Dielectric Constant
     ASTM D150
100 Hz
 
  
10 kHz
 
  
1 MHz
 
  
Dissipation Factor
     ASTM D150
100 Hz
 
  
10 kHz
 
  
1 MHz
 
  
Additional Information
Outgassing, ASTM E5955: 1.25% TML
Outgassing, ASTM E55955: 0.00% CVCM
Outgassing, ASTM E595: 1.15% WVR
Compressive Strength Yield, ASTM D695 modified, 500°C: 5500 psi
Compressive Strength Yield, ASTM D695 modified, 600°C: 3200 psi
Compressive Strain Yield, ASTM D695 modified, 500°C: 7%
Compressive Strain Yield, ASTM D695 modified, 600°C: 6%
Compressive Modulus, ASTM D695 modified, 500°C: 80000 psi
Compressive Modulus, ASTM D695 modified, 600°C: 55000 psi
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Meldin® 2030, Meldin 2030, Meldin® , Meldin, Meldin2030, 2030, Polyimide, Thermoset, Polyimide Thermoset, PI, TS, PI TS, Thermoset, TS, Saint Gobain Perf Plast, PolyimideThermoset, PITS
Features
Features may also be described by the following terms: Good Creep Resistance, Creep Resistant, Good Dimensional Stability, Dimensionally Stable, Low Friction, High Strength, Good Wear Resistance, Wear Resistant, High Temperature Strength.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.