|
Density
|
|
g/cm³
|
ISO 1183 |
|
Melt Volume-Flow Rate (MVR) (250°C/2.16 kg)
|
|
in³/10min
|
ISO 1133 |
|
Molding Shrinkage 2
|
|
|
ISO 294-4 |
|
Across Flow: 0.118 in
|
|
%
|
|
|
Flow: 0.118 in
|
|
%
|
|
|
Water Absorption
|
|
|
ISO 62 |
|
Saturation, 73°F
|
|
%
|
|
|
Equilibrium, 73°F, 50% RH
|
|
%
|
|
|
Viscosity Number 3
|
|
cm³/g
|
ISO 307 |
|
Tensile Modulus (73°F)
|
|
psi
|
ISO 527-2 |
|
Tensile Stress (Break, 73°F)
|
|
psi
|
ISO 527-2 |
|
Tensile Strain (Break, 73°F)
|
|
%
|
ISO 527-2 |
|
Charpy Notched Impact Strength (73°F)
|
|
ft·lb/in²
|
ISO 179/1eA |
|
Charpy Unnotched Impact Strength
|
|
|
ISO 179/1eU |
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
|
Heat Deflection Temperature
|
|
|
|
|
66 psi, Unannealed
|
|
°F
|
ISO 75-2/B |
|
264 psi, Unannealed
|
|
°F
|
ISO 75-2/A |
|
Melting Temperature
|
|
°F
|
ISO 11357-3 |
|
CLTE - Flow (73 to 176°F)
|
|
in/in/°F
|
ISO 11359-2 |
|
Maximum Service Temperature - Short Cycle Operation
|
|
°F
|
|
|
Specific Heat Capacity
|
|
Btu/lb/°F
|
|
|
Temperature Index - 50% Loss of Tensile Strength
|
|
|
|
|
-- 4
|
|
°F
|
|
|
-- 5
|
|
°F
|
|
|
Volume Resistivity
|
|
ohm·cm
|
IEC 60093 |
|
Relative Permittivity
|
|
|
IEC 60250 |
|
73°F, 100 Hz
|
|
|
|
|
73°F, 1 MHz
|
|
|
|
|
Dissipation Factor
|
|
|
IEC 60250 |
|
73°F, 100 Hz
|
|
|
|
|
73°F, 1 MHz
|
|
|
|
|
Comparative Tracking Index
|
|
|
IEC 60112 |
|
Solution A
|
|
V
|
|
|
Solution B
|
|
V
|
|
|
Flame Rating - UL
|
|
|
UL 94 |
|
0.0315 in
|
|
|
|
|
0.0630 in
|
|
|
|
|
Flammability by Electrical Sources of Ignition 6 (0.16 in)
|
|
|
IEC 60707 |
|
Automotive Materials (> 39.4 mil)
|
|
|
FMVSS 302 |
|
ISO Shortname
|
|
|
ISO 7792 |
|
Polymer Abbreviation
|
|
|
|
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Ultradur® B 4406 G2, Ultradur B 4406 G2, Ultradur® , Ultradur, UltradurB4406G2, B 4406 G 2, B 4406 G2, B4406, 4406G, G2, B4406G2, Polybutylene Terephthalate, PBT, Polyester, BASF, PolybutyleneTerephthalate, 4406B
|
|
Uses may also be described by the following terms: Housings, Housing.
|
|
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): OPEL (1).
|
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1).
|