| Density |
|
g/cm³
|
ISO 1183 |
| Melt Volume-Flow Rate (MVR) (250°C/2.16 kg) |
|
in³/10min
|
ISO 1133 |
| Molding Shrinkage 2 |
|
|
ISO 294-4 |
|
Across Flow: 0.118 in
|
|
%
|
|
|
Flow: 0.118 in
|
|
%
|
|
| Water Absorption |
|
|
ISO 62 |
|
Saturation, 73°F
|
|
%
|
|
|
Equilibrium, 73°F, 50% RH
|
|
%
|
|
| Viscosity Number 3 |
|
cm³/g
|
ISO 307 |
| Tensile Modulus (73°F) |
|
psi
|
ISO 527-2 |
| Tensile Stress (Break, 73°F) |
|
psi
|
ISO 527-2 |
| Tensile Strain |
|
|
|
|
Yield, 73°F
|
|
%
|
ISO 527-2/50 |
|
Break, 73°F
|
|
%
|
ISO 527-2 |
| Tensile Creep Modulus (1000 hr) |
|
psi
|
ISO 899-1 |
| Flexural Strength (73°F) |
|
psi
|
ISO 178 |
| Charpy Notched Impact Strength (73°F) |
|
ft·lb/in²
|
ISO 179/1eA |
| Charpy Unnotched Impact Strength |
|
|
ISO 179/1eU |
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
| Ball Indentation Hardness (H 358/30) |
|
psi
|
ISO 2039-1 |
| Heat Deflection Temperature |
|
|
|
|
66 psi, Unannealed
|
|
°F
|
ISO 75-2/B |
|
264 psi, Unannealed
|
|
°F
|
ISO 75-2/A |
| Melting Temperature |
|
°F
|
ISO 11357-3 |
| CLTE - Flow (73 to 176°F) |
|
in/in/°F
|
ISO 11359-2 |
| Thermal Conductivity |
|
Btu·in/hr/ft²/°F
|
DIN 52612 |
| Maximum Service Temperature - Short Cycle Operation |
|
°F
|
|
| Specific Heat Capacity |
|
Btu/lb/°F
|
|
| Temperature Index - 50% Loss of Tensile Strength |
|
|
IEC 60216 |
|
-- 4
|
|
°F
|
|
|
-- 5
|
|
°F
|
|
| Volume Resistivity |
|
ohm·cm
|
IEC 60093 |
| Relative Permittivity |
|
|
IEC 60250 |
|
73°F, 100 Hz
|
|
|
|
|
73°F, 1 MHz
|
|
|
|
| Dissipation Factor |
|
|
IEC 60250 |
|
73°F, 100 Hz
|
|
|
|
|
73°F, 1 MHz
|
|
|
|
| Comparative Tracking Index |
|
|
IEC 60112 |
|
Solution A
|
|
V
|
|
|
Solution B
|
|
V
|
|
| Flame Rating - UL |
|
|
UL 94 |
|
0.0157 in
|
|
|
|
|
0.0630 in
|
|
|
|
| Flammability by Electrical Sources of Ignition 6 (0.16 in) |
|
|
IEC 60707 |
| ISO Type |
|
|
ISO 7792 |
| Polymer Abbreviation |
|
|
|
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Ultradur® B 4300 K4, Ultradur B 4300 K4, Ultradur® , Ultradur, UltradurB4300K4, B 4300 K 4, B 4300 K4, B4300, 4300K, K4, B4300K4, Polybutylene Terephthalate, PBT, Polyester, BASF, PolybutyleneTerephthalate, 4300B
|
|
Features may also be described by the following terms: Low Warpage, Low Warp.
|
|
Uses may also be described by the following terms: Housings, Housing, Engineering Parts.
|
|
This plastic material has approval for 2 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): OPEL (1), FORD (1).
|
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1).
|