IDES Prospector Already have an account? Login Here

IDES

Luran® S KR 2859

Acrylonitrile Styrene Acrylate

Supplied by Styrolution

The technical datasheet with complete property values for Luran® S KR 2859 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Stiff extrusions product, versatile grade for profile and sheet extrusion as protective cap layer.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Good Stiffness
Uses 
  • Profiles
  • Sheet
  
Agency Ratings 
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Injection Molding
  • Profile Extrusion
  • Sheet Extrusion
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (220°C/10.0 kg)
in³/10min
 ISO 1133
Water Absorption
     ISO 62
73°F, 24 hr
%
  
Saturation, 73°F
%
  
Equilibrium, 73°F, 50% RH
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (73°F)
psi
 ISO 527-2
Tensile Stress (Yield, 73°F)
psi
 ISO 527-2/50
Tensile Strain (Yield, 73°F)
%
 ISO 527-2/50
Nominal Tensile Strain at Break (73°F)
%
 ISO 527-2/50
Tensile Creep Modulus (1000 hr)
psi
 ISO 899-1
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/1eU
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/B50
CLTE - Flow (73 to 176°F)
in/in/°F
 ISO 11359-2
Thermal Conductivity
Btu·in/hr/ft²/°F
 ISO 8302
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Additional Information
The value listed as Thermal Conductivity, ISO 8302, was tested in accordance with DIN 52612-2.
Maximum Service Temperature (Short Cycle Operation): 80°C
Blow Molding Melt Temperature: 210 to 230C
Blow Molding Mold Temperature: 60°C
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Luran® S KR 2859, Luran S KR 2859, Luran® S , Luran S, LuranSKR2859, LuranS, SKR 2859, SKR2859, KR 2859, KR2859, Acrylonitrile Styrene Acrylate, ASA, Styrolution, AcrylonitrileStyreneAcrylate, 2859KR, 2859SKR
Features
Features may also be described by the following terms: Good Stiffness.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Extrusion Notes
Pipe Extrusion Melt Temperature: 200 to 240°C
Plate Extrusion Melt Temperature: 230 to 270°C
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.