IDES Prospector Already have an account? Login Here

IDES

Adflex KS089P

Polyolefin

Supplied by LyondellBasell Industries

The technical datasheet with complete property values for Adflex KS089P is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
This information has been secured during the course of product development.
Both the product and its properties are subject to change before final commercialization.
"Adflex" KS089P thermoplastic olefin resin with slip and antiblock, is designed for air quenched blown film applications. It is based on proprietary Basell process technology.
"Adflex" KS089P resin meets FDA requirements in the Code of Federal Regulations in 21 CFR 177.2600 for rubber articles for repeated use. The final item is subject to the extraction requirements in 21 CFR 177.2600. All ingredients meet the chemical registration requirements of TSCA (U.S.) and DSL (Canada).
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Latin America
  • North America
  
Additive 
  • Antiblock
  • Slip
  
Features 
  • Antiblocking
  • Good Tear Strength
  • Puncture Resistant
  • Slip
  • Steam Resistant
Uses 
  • Film
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Blown Film
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Coefficient of Friction
     ASTM D1894
vs. Itself - Dynamic
 
  
vs. Itself - Static
 
  
Films
Nominal Value
Unit
Test Method
Secant Modulus
     ASTM D882
2% Secant, MD: 1.0 mil
psi
  
2% Secant, TD: 1.0 mil
psi
  
Tensile Strength
     ASTM D882
MD: Yield, 1.0 mil
psi
  
TD: Yield, 1.0 mil
psi
  
MD: Break, 1.0 mil
psi
  
TD: Break, 1.0 mil
psi
  
Tensile Elongation
     ASTM D882
MD: Yield, 1.0 mil
%
  
TD: Yield, 1.0 mil
%
  
MD: Break, 1.0 mil
%
  
TD: Break, 1.0 mil
%
  
Dart Drop Impact (1.0 mil)
g
 ASTM D1709A
Elmendorf Tear Strength
     ASTM D1922
MD: 1.0 mil
g
  
TD: 1.0 mil
g
  
Water Vapor Transmission
g/100 in²/24 hr
 ASTM E96
Optical
Nominal Value
Unit
Test Method
Gloss (45°, 1.00 mil)
 
 ASTM D2457
Haze (1.00 mil)
%
 ASTM D1003
Additional Information
The value listed as Gloss (45°), ASTM D2457, was tested in accordance with ASTM D523.
Film property values shown were determined on 1.0 mil thickness blown film extruded at 460°F, 2.5:1 BUR, with a 60 mil die gap.
Water Vapor Transmission, ASTM E96, Procedure E: 1.6 g/100 in²/day
Related Terminology
This supplier and product may also be known by these terms: LyondellBasell Industries, Lyondell, Basell, Bassell, Basell Polyolefins, Bassel

Product names can be difficult to match. You may have searched any one of these terms to find this product: Adflex KS089P, Adflex , AdflexKS089P, KS 089 P, KS089P, KS089, 089P, Polyolefin, Unspecified, Polyolefin Unspecified, Polyolefin, LyondellBasell, PolyolefinUnspecified, 089KS
Features
Features may also be described by the following terms: Good Puncture Resistance, Puncture Resistant, Good Tear Strength, Slip, Unspecified Slip, Antiblocking, Unspecified Antiblock.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.