IDES Prospector Already have an account? Login Here

IDES

Xyron™ 500H

Polyphenylene Ether + PS

Supplied by Asahi Kasei Chemicals Corporation

The technical datasheet with complete property values for Xyron™ 500H is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage 2 (0.0787 in)
%
 Internal Method
Water Absorption (73°F, 24 hr)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield, 73°F)
psi
 ISO 527-2
Nominal Tensile Strain at Break (73°F)
%
 ISO 527-2
Flexural Modulus (73°F)
psi
 ISO 178
Flexural Strength (73°F)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength 3 (73°F)
ft·lb/in²
 ISO 179
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
      
264 psi, Unannealed
°F
 ASTM D648
264 psi, Unannealed
°F
 ISO 75-2/A
CLTE - Flow (-22 to 149°F)
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity (73°F)
ohm·cm
 IEC 60093
Dielectric Constant
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Dissipation Factor
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Electric Strength 4 (0.0787 in)
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0591 in)
 
 UL 94
Related Terminology
This supplier and product may also be known by these terms: Thermofil, Asahi Thermofil

Product names can be difficult to match. You may have searched any one of these terms to find this product: Xyron™ 500H, Xyron 500H, Xyron™ , Xyron, Xyron500H, 500 H, 500H, Polyphenylene Ether + PS, Polyphenylene Ether PS, Polyphenylene Ether : PS, Polyphenylene Ether / PS, Polyphenylene Ether - PS, Polyphenylene Ether _ PS, Polyphenylene Ether PS, PPE+PS, PPEPS, PPE:PS, PPE/PS, PPE-PS, PPE_PS, PPE PS, Polyphenylene Ether, PPE, Asahi Kasei, PolyphenyleneEtherPS, PolyphenyleneEther, PolyphenyleneEther_PS, H500
Generic Name
Generic Name may also be described by the following terms: PPO.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2150x150x2 mm
34 mm
4Short Time
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.