IDES Prospector Already have an account? Login Here

IDES

Plenco 04548 (Injection)

Phenolic

Mineral Filler

Supplied by Plastics Engineering Co.

The technical datasheet with complete property values for Plenco 04548 (Injection) is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
PLENCO 04548 is a heat resistant mineral filled phenolic molding compound, offering fast cure rates and hot rigidity. Type ASTM 5948 CFG, and UL recognized under component file E40654. 04548 is available in black and brown.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Mineral Filler
Features 
  • Fast Cure
  • High Heat Resistance
  
Agency Ratings 
Appearance 
  • Black
  • Brown
  
Forms 
  • Granules
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Apparent Density
g/cm³
 ASTM D1895
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Compressive Strength
psi
 ASTM D695
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
ft·lb/in
 ASTM D256
Notched Izod Impact
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (E-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
Max. Continuous Use Temperature
°F
 ASTM D794
CLTE - Flow
in/in/°F
 ASTM E831
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength 2
V/mil
 ASTM D149
Dielectric Constant (1 MHz)
 
 ASTM D150
Dissipation Factor (1 MHz)
 
 ASTM D150
Arc Resistance
sec
 ASTM D495
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0591 in)
 
 UL 94
Oxygen Index
%
 ASTM D2863
UL File Number
 
  
UL
Nominal Value
Unit
Test Method
Comparative Tracking Index (CTI)
V
 UL 746
Additional Information
The value listed as Mold Shrink, Linear-Flow, ASTM D955 was tested according to the ASTM D6289 standard.
The value listed as Comparative Tracking Index, UL 746 was tested according to ASTM D3638.
Post Shrinkage, ASTM D6289, 72hr, 120°C: 0.34%
Drop Ball Impact, PLENCO Method: 90 J/m
Related Terminology
This supplier and product may also be known by these terms: Plenco

Product names can be difficult to match. You may have searched any one of these terms to find this product: Plenco 04548, Plenco 04548 (Injection), Plenco 04548 Injection, Plenco , Plenco04548Injection, 04548, 04548 (Injection), 04548 Injection, 04548Injection, Phenolic, Plastics Eng, Injection04548
Features
Features may also be described by the following terms: High Heat Resistance, Fast Cure, Fast Curing.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): ASTM (1).
Injection
Nominal Value
Unit
 
Suggested Shot Size
%
  
Rear Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Back Pressure
psi
  
Screw Speed
rpm
  
Cushion
in
  
Notes
1Typical properties: these are not to be construed as specifications.
2Method A (Short-Time)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.