IDES Prospector Already have an account? Login Here

IDES

PLUSTEK PA301G6

Polyamide 66

Glass Fiber Reinforcement, 30%

Supplied by Polyram Ram-On Industries

The technical datasheet with complete property values for PLUSTEK PA301G6 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
HEAT STABILIZED, 30% GLASS-FIBER REINFORCED POLYAMIDE 6.6 FOR INJECTION MOULDING APPLICATIONS.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 30% Filler by Weight
Additive 
  • Heat Stabilizer
Features 
  • Heat Stabilized
RoHS Compliance 
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Molding Shrinkage
      
Flow
in/in
 ASTM D955
--
%
 ISO 2577
Water Absorption
      
Saturation
%
 ASTM D570
Saturation, 73°F
%
 ISO 62
Equilibrium, 73°F, 50% RH
%
 ASTM D570, ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638, ISO 527-2
Tensile Strength (Yield)
psi
 ASTM D638, ISO 527-2
Tensile Elongation (Break)
%
 ASTM D638, ISO 527-2
Flexural Modulus
psi
 ASTM D790, ISO 178
Flexural Strength
psi
 ASTM D790, ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
      
73°F
ft·lb/in
 ASTM D256
73°F
ft·lb/in²
 ISO 180
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785, ISO 2039-2
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
      
66 psi, Unannealed
°F
 ASTM D648, ISO 75-2/B
264 psi, Unannealed
°F
 ASTM D648, ISO 75-2/A
Maximum Use Temperature - Short Peaks Operation
°F
  
Melting Temperature
°F
 ISO 11357-3, ASTM D3417
Maximum Continuous Use Temperature
°F
  
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Dielectric Constant (1 MHz)
 
 IEC 60250
Comparative Tracking Index
V
 IEC 60112
Electric Strength
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.118 in)
 
 UL 94
Glow Wire Flammability Index
°F
 IEC 60695-2-12
Glow Wire Ignition Temperature
°F
 IEC 60695-2-13
Flammability
mm/min
 FMVSS 302
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: PLUSTEK PA301G6, PLUSTEK , PLUSTEKPA301G6, PA 301 G 6, PA301G6, PA301, 301G, G6, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Polyram, Polyamide66, Nylon66, 301PA
Generic Name
Generic Name may also be described by the following terms: PA66.
Features
Features may also be described by the following terms: Heat Stabilized, Heat-ageing Stabilized, Heat Ageing Stabilized, Heat-aging Stabilized, Heat Aging Stabilized.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Holding Pressure
psi
  
Back Pressure
psi
  
Screw Speed
rpm
  
Injection Notes
Fill Speed: 50 to 75 mm/sec
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.