IDES Prospector Already have an account? Login Here

IDES

NORYL* APS130 Resin

Polyphenylene Sulfide + PPE

Supplied by SABIC Innovative Plastics Asia Pacific

The technical datasheet with complete property values for NORYL* APS130 Resin is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (300°C/5.0 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow (0.126 in)
in/in
 Internal Method
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield)
psi
 Internal Method
Tensile Elongation (Break)
%
 Internal Method
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed, 0.126 in)
°F
 ASTM D648
CLTE - Flow (-22 to 86°F)
in/in/°F
 ASTM E831
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257
Dielectric Strength (0.0630 in, in Oil)
V/mil
 ASTM D149
Dielectric Constant     ASTM D150
50 Hz
 
  
60 Hz
 
  
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics

Product names can be difficult to match. You may have searched any one of these terms to find this product: NORYL* APS130 Resin, NORYL APS130 Resin, NORYL* , NORYL, NORYLAPS130Resin, APS 130 Resin, APS130 Resin, APS130, 130Resin, APS130Resin, Polyphenylene Sulfide + PPE, Polyphenylene Sulfide PPE, Polyphenylene Sulfide : PPE, Polyphenylene Sulfide / PPE, Polyphenylene Sulfide - PPE, Polyphenylene Sulfide _ PPE, Polyphenylene Sulfide PPE, PPS+PPE, PPSPPE, PPS:PPE, PPS/PPE, PPS-PPE, PPS_PPE, PPS PPE, Polyphenylene Sulfide, PPS, SABIC IP Asia, PolyphenyleneSulfidePPE, PolyphenyleneSulfide, PolyphenyleneSulfide_PPE, 130APS
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Drying Time, Maximum
hr
  
Suggested Max Moisture
%
  
Suggested Shot Size
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Vent Depth
in
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.