IDES Prospector Already have an account? Login Here

IDES

Xantar® G6F 23 R

Polycarbonate

Glass Fiber Reinforcement, 30%

Supplied by Mitsubishi Engineering-Plastics Corp

The technical datasheet with complete property values for Xantar® G6F 23 R is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
  • North America
  
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 30% Filler by Weight
Additive 
  • Flame Retardant
  • Mold Release
  
Features 
  • Flame Retardant
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
      
--
g/cm³
 ISO 1183
--
lb/in³
 ISO 1183 2
Melt Volume-Flow Rate (MVR) (300°C/1.2 kg)
in³/10min
 ISO 1133
Molding Shrinkage
     ISO 294-4
Across Flow
%
  
Flow
%
  
Water Absorption
      
Saturation, 73°F
%
 ISO 62
Saturation
%
 ISO 62 2
Limiting Viscosity Number
in³/lb
 ISO 1628-4
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
      
--
psi
 ISO 527-2
--
psi
 ISO 527-2 2
Tensile Stress
      
Break
psi
 ISO 527-2
Break
psi
 ISO 527-2 2
Tensile Strain (Break)
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Flexural Strength
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact Strength (73°F)
ft·lb/in²
 ISO 180/1A
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
 ISO 2039-2
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
264 psi, Unannealed
°F
 ISO 75-2/A
264 psi
°F
 ISO 75-2 2
Vicat Softening Temperature
      
--
°F
 ISO 306/B50
50°C/h, B (50N)
°F
 ISO 306 2
Ball Pressure Test (257°F)
 
 IEC 60695-10-2
CLTE - Flow
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
      
--
ohm·cm
 IEC 60093
--
ohm·in
 IEC 60093 2
Relative Permittivity
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Dissipation Factor
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Comparative Tracking Index
      
--
V
 IEC 60112
--
 
 IEC 60112 2
Electric Strength
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Burning Behav. at 1.6mm nom. thickn. (0.06 in, UL)
 
 ISO 1210 2
Burning Behav. at thickness h (0.118 in, UL)
 
 ISO 1210 2
Flammability Classification
     IEC 60695-11-10, -20
0.0591 in
 
  
0.118 in
 
  
Glow Wire Flammability Index
     IEC 60695-2-12
0.0591 in
°F
  
0.118 in
°F
  
Glow Wire Ignition Temperature
     IEC 60695-2-13
0.0591 in
°F
  
0.118 in
°F
  
Oxygen Index
      
--
%
 ISO 4589-2
--
%
 ISO 4589-2 2
UL
Nominal Value
Unit
Test Method
RTI Str
     UL 746
0.0591 in
°F
  
0.118 in
°F
  
RTI Imp
     UL 746
0.0591 in
°F
  
0.118 in
°F
  
RTI Elec
     UL 746
0.0591 in
°F
  
0.118 in
°F
  
Comparative Tracking Index (CTI) (PLC)
 
 UL 746
Fill Analysis
Nominal Value
Unit
Test Method
Thermal Conductivity of Melt
Btu·in/hr/ft²/°F
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Xantar® G6F 23 R, Xantar G6F 23 R, Xantar® , Xantar, XantarG6F23R, G 6 F 23 R, G6F 23 R, G6, 6F, F23, 23R, G6F23R, Polycarbonate, PC, Mitsubishi EP, 6G
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Suggested Shot Size
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Back Pressure
psi
  
Screw L/D Ratio
 
  
Screw Compression Ratio
 
  
Notes
1Typical properties: these are not to be construed as specifications.
2Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.