Beetle MD82 Teknor Apex Chem Poly Polyamide 6

Product Description

MD82 is a UL recognised, V-0 rated, halogen & phosphorus free flame retarded, unreinforced injection moulding grade of nylon 6.

General

Material Status

Commercial: Active

Availability

Europe

North America

Features

Flame Retardant

Halogen Free

Low (to None) Phosphorus Content

Forms

Pellets

Processing Method

Injection Molding

Physical	Dry	Conditioned	Unit	Test Method
Density		--	g/cm³	ISO 1183
Molding Shrinkage²		--	%	Internal Method
Mechanical	Dry	Conditioned	Unit	Test Method
Tensile Modulus			psi	ISO 527-2
Tensile Stress (Break)			psi	ISO 527-2
Tensile Strain (Break)			%	ISO 527-2
Flexural Modulus			psi	ISO 178
Flexural Strength³			psi	ISO 178
Impact	Dry	Conditioned	Unit	Test Method
Charpy Notched Impact Strength			ft·lb/in²	ISO 179
Charpy Unnotched Impact Strength			ft·lb/in²	ISO 179
Notched Izod Impact Strength		--	ft·lb/in²	ISO 180
Unnotched Izod Impact Strength		--		ISO 180
Thermal	Dry	Conditioned	Unit	Test Method
Heat Deflection Temperature (264 psi, Unannealed)			°F	ISO 75-2/A
CLTE - Flow		--	in/in/°F	TMA
Thermal Conductivity		--	Btu·in/hr/ft²/°F	BS 874
Electrical	Dry	Conditioned	Unit	Test Method
Surface Resistivity			ohms	IEC 60093
Volume Resistivity			ohm·cm	IEC 60093
Relative Permittivity (1 MHz)				IEC 60250
Dissipation Factor (1 MHz)				IEC 60250
Comparative Tracking Index			V	IEC 60112
Electric Strength (0.118 in)			V/mil	IEC 60243-1
Flammability	Dry	Conditioned	Unit	Test Method
Flame Rating - UL (0.0248 in)		--		UL 94
Glow Wire Flammability Index				IEC 60695-2-12
0.0394 in		--	°F
0.0591 in		--	°F
Glow Wire Ignition Temperature				IEC 60695-2-13
0.0394 in		--	°F
0.0591 in		--	°F
Oxygen Index		--	%	ISO 4589-2
Related Terminology
Dry	Product names can be difficult to match. You may have searched any one of these terms to find this product: Beetle® MD82, Beetle MD82, Beetle® , Beetle, BeetleMD82, MD 82, MD82, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, Teknor Apex Chem Poly, Polyamide6, Nylon6, 82MD
Generic Name
Dry	Generic Name may also be described by the following terms: PA6.
Conditioned	Generic Name may also be described by the following terms: PA6.
Features
Dry	Features may also be described by the following terms: Zero Halogen Content, Halogen Free, Low Phosphorus Content.
Conditioned	Product names can be difficult to match. You may have searched any one of these terms to find this product: Beetle® MD82, Beetle MD82, Beetle® , Beetle, BeetleMD82, MD 82, MD82, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, Teknor Apex Chem Poly, Polyamide6, Nylon6, 82MD

Injection	Dry	Unit
Drying Temperature		°F
Drying Time		hr
Rear Temperature		°F
Middle Temperature		°F
Front Temperature		°F
Processing (Melt) Temp		°F
Mold Temperature		°F
Injection Rate
Screw Speed		rpm
Injection Notes
Back pressure: Low Injection pressure: High No drying is necessary unless the materials has been exposed to air for longer than three hours.

Notes

¹Typical properties: these are not to be construed as specifications.

²Mould shrinkage is significantly influenced by many factors including wall thickness, gating, moulding shape and processing conditions. The range values given are determined from specimen bar mouldings of 1.5 mm to 4 mm wall thickness. They are provided as a guide for comparison purposes only and no guarantee should be inferred from their inclusion. (Specimens measured in the dry state, 24 hours after moulding).

³At conventional deflection

Beetle® MD82

Polyamide 6

Supplied by Teknor Apex Company (Chem Polymer)