IDES Prospector Already have an account? Login Here

IDES

Formolene® 2810A

Thermoplastic Polyolefin Elastomer

Supplied by Formosa Plastics Corporation, U.S.A.

The technical datasheet with complete property values for Formolene® 2810A is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Formolene 2810A is a RTPO made with the latest gas phase technology containing approximately 25% ethylene-propylene rubber (EPR). It exhibits an excellent balance of physical and thermodynamic properties which make it an ideal choice for critical applications in the areas of automotive, appliances, lawn & garden, medical, and rigid packaging. It exhibits outstanding cold temperature impact resistance and ESCR coupled with a good balance of flexural and tensile strength. Ease of processability and recyclability along with a broad service temperature range make it ideal for applications where engineering thermoplastics or compounded homopolymer/EPDM blends are used.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Good Processability
  • High ESCR (Stress Crack Resist.)
  • Low Temperature Impact Resistance
  • Recyclable Material
  
Uses 
  • Appliances
  • Automotive Applications
  • Medical/Healthcare Applications
  • Rigid Packaging
  
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (Yield, Injection Molded)
psi
 ASTM D638
Tensile Elongation 2 (Yield, Injection Molded)
%
 ASTM D638
Flexural Modulus - 1% Secant 3 (Injection Molded)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F, Injection Molded)
ft·lb/in
 ASTM D256
Notched Izod Impact
     ASTM D256
-18°F, Injection Molded
ft·lb/in
  
73°F, Injection Molded
 
  
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed, Injection Molded
°F
  
264 psi, Unannealed, Injection Molded
°F
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Formolene® 2810A, Formolene 2810A, Formolene® , Formolene, Formolene2810A, 2810 A, 2810A, TPO, Thermoplastic Polyolefin Elastomer, TPO (POE), TPO POE, Thermoplastic Elastomer, TPE, Formosa Plastics, ThermoplasticPolyolefinElastomer, TPOPOE, ThermoplasticElastomer, A2810
Features
Features may also be described by the following terms: Good Processability, Easy Processing, Low Temperatuer Impact Resistance, Low Temp Impact Resistance, High Environmental Stress Cracking Resistance, High ESCR, Stress Cracking Resistant.
Uses
Uses may also be described by the following terms: Rigid Packaging, Automotive Applications, Automotive Sector, Medical Applications.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1).
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
30.051 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.