IDES Prospector Already have an account? Login Here

IDES

INEOS HDPE J50-1000-178

High Density Polyethylene

Supplied by INEOS Olefins & Polymers USA

The technical datasheet with complete property values for INEOS HDPE J50-1000-178 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
J50-1000-178 is a high density polyethylene copolymer intended for the injection molding of closures for beverages. Because of its high purity and excellent organoleptic properties, this grade is certified as low taste and is intended for packaging in direct contact with beverages. This material meets the Food and Drug Administration requirements of 21CFR 177.1520.

Typical Applications
  • Caps and closures for the packaging of still water
  • Injection molded applications where low taste and odor are critical.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Copolymer
  • Food Contact Acceptable
  • Good Organoleptic Properties
  • High Purity
  • Low to No Odor
  • Low to No Taste
  • Narrow Molecular Weight Distribution
Uses 
  • Caps
  • Closures
  
Agency Ratings 
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D4883
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Environmental Stress-Cracking Resistance (100% Igepal)
hr
 ASTM D1693B
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (Yield)
psi
 ASTM D638
Tensile Elongation 2 (Break)
%
 ASTM D638
Flexural Modulus - Tangent
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (66 psi, Unannealed)
°F
 ASTM D648
Brittleness Temperature
°F
 ASTM D746
Vicat Softening Temperature
°F
 ASTM D1525
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: INEOS HDPE J50-1000-178, INEOS HDPE J501000178, INEOS HDPE , INEOSHDPEJ501000178, INEOSHDPE, J 50, HDPEJ 50 1000 178, HDPEJ 50, HDPEJ50-1000-178, HDPEJ501000178, HDPEJ50:1000:178, HDPEJ50/1000/178, HDPEJ50+1000+178, HDPEJ50_1000_178, HDPEJ50 1000 178, HDPEJ50, J 50 1000 178, J50-1000-178, J501000178, J50:1000:178, J50/1000/178, J50+1000+178, J50_1000_178, J50 1000 178, J50, 501000, 1000178, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, Ineos USA, PolyethyleneHighDensity, 50J, 50HDPEJ
Features
Features may also be described by the following terms: Narrow Molecular Weight Distribution, Narrow MW Distribution, Low Odor, Good Organoleptic Properties, High Purity, Low Taste.
Uses
Uses may also be described by the following terms: Closure Caps, Caps, Cap.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.