IDES Prospector Already have an account? Login Here

IDES

Bayblend® KU 2-1514

Acrylonitrile Butadiene Styrene + PC

Supplied by Bayer MaterialScience AG

The technical datasheet with complete property values for Bayblend® KU 2-1514 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
High heat resistant injection molding grade; ball indentation temperature >=125 °C; Vicat/B 120 temperature = 136 °C; UL-listing 94 V-0 at 1.5 mm; suitable for supporting life components.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Europe
  
Features 
  • High Heat Resistance
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Multi-Point Data 
  • Viscosity vs. Shear Rate (ISO 11403-2)
Physical
Nominal Value
Unit
Test Method
Density
lb/in³
 ISO 1183 2
Melt volume-flow rate (260°C/5.0 kg)
in³/10min
 ISO 1133 2
Molding Shrinkage
     ISO 2577 2
Flow
%
  
Across Flow
%
  
Water Absorption
     ISO 62 2
Saturation
%
  
Equilibrium
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile modulus
psi
 ISO 527-2 2
Tensile Stress
      
Yield
psi
 ISO 527-2 2
Break
psi
 ISO 527-2/50
Tensile Strain
      
Yield
%
 ISO 527-2 2
Break
%
 ISO 527-2/50
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact Strength
     ISO 180/A
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Unnotched Izod Impact Strength (73°F)
 
 ISO 180
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ISO 75-2 2
66 psi
°F
  
264 psi
°F
  
Vicat Softening Temperature
      
--
°F
 ISO 306/B120
50°C/h, B (50N)
°F
 ISO 306 2
CLTE
     ISO 11359-2 2
Flow
in/in/°F
  
Transverse
in/in/°F
  
Electrical
Nominal Value
Unit
Test Method
Surface resistivity
ohms
 IEC 60093 2
Volume resistivity
ohm·in
 IEC 60093 2
Relative Permittivity
     IEC 60250 2
100 Hz
 
  
1 MHz
 
  
Dissipation Factor
     IEC 60250 2
100 Hz
 
  
1 MHz
 
  
Comparative tracking index
 
 IEC 60112 2
Electric strength
V/mil
 IEC 60243-1 2
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0591 in
 
  
0.0787 in
 
  
0.118 in
 
  
Fill Analysis
Nominal Value
Unit
Test Method
Melt Viscosity 3 (500°F)
Pa·s
 ISO 11443
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Bayblend® KU 2-1514, Bayblend KU 21514, Bayblend® , Bayblend, BayblendKU21514, KU 2, KU 2-1514, KU 21514, KU 2:1514, KU 2/1514, KU 2+1514, KU 2_1514, KU 2 1514, KU2, 21514, KU21514, KU2_1514, Acrylonitrile Butadiene Styrene + PC, Acrylonitrile Butadiene Styrene PC, Acrylonitrile Butadiene Styrene : PC, Acrylonitrile Butadiene Styrene / PC, Acrylonitrile Butadiene Styrene - PC, Acrylonitrile Butadiene Styrene _ PC, Acrylonitrile Butadiene Styrene PC, ABS+PC, ABSPC, ABS:PC, ABS/PC, ABS-PC, ABS_PC, ABS PC, Acrylonitrile Butadiene Styrene, ABS, Bayer Euro, AcrylonitrileButadieneStyrenePC, AcrylonitrileButadieneStyrene, AcrylonitrileButadieneStyrene_PC, 2KU
Features
Features may also be described by the following terms: High Heat Resistance.
Notes
1Typical properties: these are not to be construed as specifications.
2Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted.
31000 1/s
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.