IDES Prospector Already have an account? Login Here

IDES

Marlex® PP AGM-350

Polypropylene Impact Copolymer

Supplied by Phillips Sumika Polypropylene Company

The technical datasheet with complete property values for Marlex® PP AGM-350 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Impact Copolymer
  • Low Temperature Impact Resistance
  
Uses 
  • Automotive Interior Trim
Automotive Specifications 
 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ISO 1133
Molding Shrinkage (73°F, 48 hr, 0.118 in)
%
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield, Injection Molded)
psi
 ISO 527-2/50
Flexural Modulus 2 (Injection Molded)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact Strength
     ISO 180
-40°F, Injection Molded
ft·lb/in²
  
73°F, Injection Molded
ft·lb/in²
  
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ISO 2039-2
Shore Hardness (Shore D, Injection Molded)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Marlex® PP AGM-350, Marlex PP AGM350, Marlex® PP , Marlex PP, MarlexPPAGM350, MarlexPP, AGM, PPAGM-350, PPAGM350, PPAGM:350, PPAGM/350, PPAGM+350, PPAGM_350, PPAGM 350, PPAGM, AGM-350, AGM350, AGM:350, AGM/350, AGM+350, AGM_350, AGM 350, Polypropylene Impact Copolymer, PP Impact Copolymer, Polypropylene, PP, Phillips Sumika, PolypropyleneImpactCopolymer, PPImpactCopolymer, 350AGM, 350PPAGM
Features
Features may also be described by the following terms: Impact Copolymer, Low Temperatuer Impact Resistance, Low Temp Impact Resistance.
Automotive Specifications
This plastic material has approval for 4 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): GM (4).
Injection
Nominal Value
Unit
 
Suggested Shot Size
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Injection Notes
Melt temperature above 500°F (260°C) may cause degredation and changes to resin properties.
First stage injection pressure: Maximize
Screw speed: 30 to 60%
Packaging pressure: Minimize
Notes
1Typical properties: these are not to be construed as specifications.
20.079 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.