IDES Prospector Already have an account? Login Here

IDES

Durolon® IR2500 CR010

Polycarbonate

Supplied by Unigel Plásticos

The technical datasheet with complete property values for Durolon® IR2500 CR010 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
  • Latin America
  • North America
  • South America
  
Additive 
  • Mold Release
Features 
  • Food Contact Acceptable
  • Good Mold Release
  • Medium Viscosity
Uses 
  • Bottles
  • Medical/Healthcare Applications
  
Agency Ratings 
Appearance 
  • Clear - Blue Tint
  • Colors Available
  
Forms 
  • Pellets
Processing Method 
  • Blow Molding
  • Injection Blow Molding
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (300°C/1.2 kg)
g/10 min
 ASTM D1238, ISO 1133
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (73°F, 24 hr)
%
 ASTM D570, ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638, ISO 527-2
Tensile Strength
     ASTM D638, ISO 527-2
Yield
psi
  
Break
psi
  
Tensile Elongation (Break)
%
 ASTM D638, ISO 527-2
Flexural Modulus
psi
 ASTM D790, ISO 178
Flexural Strength
psi
 ASTM D790, ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.126 in)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness
     ASTM D785
M-Scale
 
  
R-Scale
 
  
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648, ISO 75-2/A
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength (0.0630 in)
V/mil
 ASTM D149
Dielectric Constant
     ASTM D150
60 Hz
 
  
1 MHz
 
  
Dissipation Factor
     ASTM D150
60 Hz
 
  
1 MHz
 
  
Arc Resistance
sec
 ASTM D495
Flammability
Nominal Value
Unit
Test Method
Glow Wire Ignition Temperature (0.126 in)
°F
 IEC 60695-2-13
Optical
Nominal Value
Unit
Test Method
Refractive Index
 
 ASTM D542, ISO 489
Transmittance
%
 ASTM D1003
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Durolon® IR2500 CR010, Durolon IR2500 CR010, Durolon® , Durolon, DurolonIR2500CR010, IR 2500 CR 010, IR2500 CR010, IR2500, 2500CR, CR010, IR2500CR010, Polycarbonate, PC, Unigel, 2500IR
Features
Features may also be described by the following terms: Medium Viscosity, Good Mold Release, Easy Release, Good Demolding.
Uses
Uses may also be described by the following terms: Medical Applications.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.