Beetle 66GF6 Teknor Apex Chem Poly Polyamide 66 (Glass Fiber Reinforcement, 30%)

Product Description

66GF6 is a 30% glass fibre reinforced nylon 66 that offers good mechanical performance coupled with good surface finish and flow.

General

Material Status

Commercial: Active

Availability

Europe

North America

Filler / Reinforcement

Glass Fiber Reinforcement, 30% Filler by Weight

Features

Good Flow

Good Surface Finish

Processing Method

Injection Molding

Physical	Dry	Conditioned	Unit	Test Method
Density		--	g/cm³	ISO 1183
Molding Shrinkage²		--	%	Internal Method
Water Absorption (Equilibrium, 73°F, 50% RH)		--	%	ISO 62
Mechanical	Dry	Conditioned	Unit	Test Method
Tensile Modulus			psi	ISO 527-2
Tensile Stress (Yield)			psi	ISO 527-2
Tensile Strain (Break)			%	ISO 527-2
Flexural Modulus			psi	ISO 178
Flexural Strength				ISO 178
--³	--		psi
--⁴		--	psi
Impact	Dry	Conditioned	Unit	Test Method
Notched Izod Impact Strength			ft·lb/in²	ISO 180
Unnotched Izod Impact Strength				ISO 180
Thermal	Dry	Conditioned	Unit	Test Method
Heat Deflection Temperature
66 psi, Unannealed			°F	ISO 75-2/B
264 psi, Unannealed			°F	ISO 75-2/A
Electrical	Dry	Conditioned	Unit	Test Method
Surface Resistivity			ohms	IEC 60093
Volume Resistivity			ohm·cm	IEC 60093
Relative Permittivity (1 MHz)				IEC 60250
Dissipation Factor (1 MHz)				IEC 60250
Comparative Tracking Index			V	IEC 60112
Electric Strength (0.118 in)			V/mil	IEC 60243-1
Flammability	Dry	Conditioned	Unit	Test Method
Flame Rating - UL (Teknor Apex result)				UL 94
Related Terminology
Dry	Product names can be difficult to match. You may have searched any one of these terms to find this product: Beetle® 66GF6, Beetle 66GF6, Beetle® , Beetle, Beetle66GF6, 66 GF 6, 66GF6, 66GF, GF6, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Teknor Apex Chem Poly, Polyamide66, Nylon66, GF66
Generic Name
Dry	Generic Name may also be described by the following terms: PA66.
Conditioned	Generic Name may also be described by the following terms: PA66.
Features
Dry	Features may also be described by the following terms: Good Surface Finish, Good Flow.
Conditioned	Product names can be difficult to match. You may have searched any one of these terms to find this product: Beetle® 66GF6, Beetle 66GF6, Beetle® , Beetle, Beetle66GF6, 66 GF 6, 66GF6, 66GF, GF6, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Teknor Apex Chem Poly, Polyamide66, Nylon66, GF66

Injection	Dry	Unit
Drying Temperature		°F
Drying Time		hr
Rear Temperature		°F
Middle Temperature		°F
Front Temperature		°F
Processing (Melt) Temp		°F
Mold Temperature		°F
Injection Rate
Screw Speed		rpm
Injection Notes
Back Pressure: Low Injection Pressure: High No drying is necessary unless the material has been exposed to air for longer than 3 hours.

Notes

¹Typical properties: these are not to be construed as specifications.

²Mould shrinkage is significantly influenced by many factors including wall thickness, gating, component shape and moulding conditions.
The range values stated were determined from specimen bar mouldings of 1.5mm to 4mm wall thickness. They are provided as a guide for comparison purposes only and no guarantee should be inferred from their inclusion. (Specimens measured in the dry state, 24 hours after moulding).

³At Yield

⁴At Break

Beetle® 66GF6

Polyamide 66

Glass Fiber Reinforcement, 30%

Supplied by Teknor Apex Company (Chem Polymer)