IDES Prospector Already have an account? Login Here

IDES

CYCOLAC* MG37CR Resin

Acrylonitrile Butadiene Styrene

Supplied by SABIC Innovative Plastics

The technical datasheet with complete property values for CYCOLAC* MG37CR Resin is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
High performance, injection molding ABS. Overall balance of physical properties, good processability and chemical resistance.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Good Chemical Resistance
  • Good Processability
  
Processing Method 
  • Injection Molding
Multi-Point Data 
  • Flexural DMA (ASTM D4065)
  • Specific Heat vs. Temperature (ASTM D3417)
  • Tensile Fatigue
  • Tensile Stress vs. Strain (ASTM D638)
  • Thermal Conductivity vs. Temperature (ASTM E1530)
  • Viscosity vs. Shear Rate (ASTM D3835)
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR)      
230°C/3.8 kg
g/10 min
 ASTM D1238
220°C/10.0 kg
g/10 min
 ISO 1133
Molding Shrinkage - Flow (0.126 in)
in/in
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2
psi
 ASTM D638
Tensile Strength 3     ASTM D638
Yield
psi
  
Break
psi
  
Tensile Elongation 3     ASTM D638
Yield
%
  
Break
%
  
Flexural Modulus 4 (1.97 in Span)
psi
 ASTM D790
Flexural Strength 4 (Yield, 1.97 in Span)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Instrumented Dart Impact (73°F, Total Energy)
in·lb
 ASTM D3763
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load     ASTM D648
66 psi, Unannealed, 0.126 in
°F
  
264 psi, Unannealed, 0.126 in
°F
  
Vicat Softening Temperature
°F
 ASTM D1525 5
CLTE     ASTM E831
Flow: -40 to 104°F
in/in/°F
  
Transverse: -40 to 104°F
in/in/°F
  
Electrical
Nominal Value
Unit
Test Method
Arc Resistance (PLC) 6
 
 ASTM D495
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0600 in)
 
 UL 94
UL
Nominal Value
Unit
Test Method
RTI Str
°F
 UL 746
RTI Imp
°F
 UL 746
RTI Elec
°F
 UL 746
Comparative Tracking Index (CTI) (PLC)
 
 UL 746
High Voltage Arc Tracking Rate (HVTR) (PLC)
 
 UL 746
Hot-wire Ignition (HWI) (PLC)
 
 UL 746
High Amp Arc Ignition (HAI) (PLC)
 
 UL 746
Fill Analysis
Nominal Value
Unit
Test Method
Melt Viscosity (464°F, 1000 sec^-1)
Pa·s
 ASTM D3835
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics, GE Polymerland, Cyclac

Product names can be difficult to match. You may have searched any one of these terms to find this product: CYCOLAC* MG37CR Resin, CYCOLAC MG37CR Resin, CYCOLAC* , CYCOLAC, CYCOLACMG37CRResin, MG 37 CR Resin, MG37CR Resin, MG37, 37CR, CRResin, MG37CRResin, Acrylonitrile Butadiene Styrene, ABS, SABIC IP, AcrylonitrileButadieneStyrene, 37MG
Features
Features may also be described by the following terms: Good Processability, Easy Processing, Good Chemical Resistance, Chemical Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Drying Time, Maximum
hr
  
Suggested Max Moisture
%
  
Suggested Shot Size
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Vent Depth
in
  
Notes
1Typical properties: these are not to be construed as specifications.
20.20 in/min
3Type I, 0.20 in/min
40.051 in/min
5Rate B (120°C/h), Loading 2 (50 N)
6Tungsten Electrode
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.