IDES Prospector Already have an account? Login Here

IDES

FINGERPRINT™ DFDA-7510 NT

Polyethylene Resin

Supplied by The Dow Chemical Company

The technical datasheet with complete property values for FINGERPRINT™ DFDA-7510 NT is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
FINGERPRINT™ DFDA-7510 NT Linear Low Density Polyethylene Resin is produced using UNIPOL™ process technology. It is intended for use in micro irrigation tube, durable hose and tube, profile extrusion, and injection molded fittings applications.

It also has utility as a blending component to modify and improve the physical properties of high pressure, very low density, linear low density, or high density polyethylene resins. Outdoor applications require the addition of UV stabilizer to maintain the excellent properties over extended periods of UV exposure.

Main Characteristics:
  • Outstanding ESCR
  • Excellent burst strength
  • Excellent consistency and extrusion characteristics
  • Excellent flexibility for easy roll-out

Slip Additive: none
Antiblock Additive: none

Industrial Standards Compliance:
  • ASTM D 3350: cell classification PE123110A
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Latin America
  • North America
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Profile Extrusion
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR)
     ASTM D1238
190°C/2.16 kg
g/10 min
  
190°C/21.6 kg
g/10 min
  
Environmental Stress-Cracking Resistance 2 (F0)
hr
 ASTM D1693A
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 3
     ASTM D638
Yield
psi
  
Break
psi
  
Tensile Elongation 3 (Break)
%
 ASTM D638
Flexural Modulus 3
psi
 ASTM D790
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness 3 (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Brittleness Temperature 3
°F
 ASTM D746A
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: FINGERPRINT™ DFDA-7510 NT, FINGERPRINT DFDA7510 NT, FINGERPRINT™ , FINGERPRINT, FINGERPRINTDFDA7510NT, DFDA, DFDA-7510 NT, DFDA7510 NT, DFDA:7510 NT, DFDA/7510 NT, DFDA+7510 NT, DFDA_7510 NT, DFDA 7510 NT, DFDA7510, 7510NT, DFDA7510NT, DFDA_7510NT, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, LLDPE, Polyethylene, PE, Dow, PolyethyleneLinearLowDensity, 7510DFDA
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): ASTM (1).
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Extrusion Notes
Fabrication Conditions For Blown Film:
  • Screw Type: All standard commercial extrusion equipment.
  • Melt Temperature Range: 385 - 430 °F (196 - 221 °C)
Notes
1Typical properties: these are not to be construed as specifications.
2As guided by D3350; Compression molded parts prepared according to ASTM D 1928 Procedure C. Properties will vary with changes in molding conditions and aging time.
3Compression molded parts prepared according to ASTM D 1928 Procedure C. Properties will vary with changes in molding conditions and aging time.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.