| Specific Gravity |
|
|
ASTM D792 |
| Melt Mass-Flow Rate (MFR) (337°C/6.6 kg) |
|
g/10 min
|
ASTM D1238 |
| Molding Shrinkage - Flow (0.126 in) |
|
in/in
|
Internal Method |
| Water Absorption |
|
|
ASTM D570 |
|
24 hr
|
|
%
|
|
|
Equilibrium, 73°F
|
|
%
|
|
| Tensile Modulus 2 |
|
psi
|
ASTM D638 |
| Tensile Strength 3 (Yield) |
|
psi
|
ASTM D638 |
| Tensile Elongation 3 |
|
|
ASTM D638 |
|
Yield
|
|
%
|
|
|
Break
|
|
%
|
|
| Flexural Modulus 4 (3.94 in Span) |
|
psi
|
ASTM D790 |
| Flexural Strength 4 (Yield, 3.94 in Span) |
|
psi
|
ASTM D790 |
| Poisson's Ratio |
|
|
ASTM D638 |
| Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel) |
|
mg
|
ASTM D1044 |
| Notched Izod Impact (73°F) |
|
ft·lb/in
|
ASTM D256 |
| Unnotched Izod Impact (73°F) |
|
ft·lb/in
|
ASTM D4812 |
| Reverse Notch Izod Impact (0.126 in) |
|
ft·lb/in
|
ASTM D256 |
| Gardner Impact (73°F) |
|
in·lb
|
ASTM D3029 |
| Rockwell Hardness (M-Scale) |
|
|
ASTM D785 |
| Deflection Temperature Under Load |
|
|
ASTM D648 |
|
66 psi, Unannealed, 0.252 in
|
|
°F
|
|
|
264 psi, Unannealed, 0.252 in
|
|
°F
|
|
| Vicat Softening Temperature |
|
°F
|
ASTM D1525 5 |
| CLTE |
|
|
ASTM E831 |
|
Flow: -4 to 302°F
|
|
in/in/°F
|
|
|
Transverse: -4 to 302°F
|
|
in/in/°F
|
|
| Thermal Conductivity |
|
Btu·in/hr/ft²/°F
|
ASTM C177 |
| Volume Resistivity |
|
ohm·cm
|
ASTM D257 |
| Dielectric Strength |
|
|
ASTM D149 |
|
0.0630 in, in Air
|
|
V/mil
|
|
|
0.0630 in, in Oil
|
|
V/mil
|
|
| Dielectric Constant (1 kHz) |
|
|
ASTM D150 |
| Dissipation Factor |
|
|
ASTM D150 |
|
1 kHz
|
|
|
|
|
2.45 GHz
|
|
|
|
| Oxygen Index |
|
%
|
ASTM D2863 |
| NBS Smoke Density - Flaming, Ds, 4 min |
|
|
ASTM E662 |
|
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics, GE Polymerland
Product names can be difficult to match. You may have searched any one of these terms to find this product: ULTEM* 1000M Resin, ULTEM 1000M Resin, ULTEM* , ULTEM, ULTEM1000MResin, 1000 M Resin, 1000M Resin, 1000M, MResin, 1000MResin, Polyether Imide, PEI, SABIC IP, PolyetherImide, M1000
|
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1).
|